Removal and Installation
Air Spring
▸Contents: 17 - Rear Suspension
- Description and OperationRear Suspension
- Diagnosis and TestingShock/Strut Diagnosis
- Technical SpecificationsTorque Specifications
ARM, Lower Control
Removal and Installation
- Lower Control Arm Without Trx
- Lower Control Arm With Trx
ARM, Upper Control
Removal and Installation
- Upper Control Arm Without Trx
- Upper Control Arm With Trx
BUMPER, Jounce
- Removal and InstallationJounce Bumper
DAMPER, Power Hop
- Removal and InstallationPower Hop Damper
LINK, Stabilizer Bar
- Removal and InstallationStabilizer Bar Link
SHOCK ABSORBER, Suspension
Removal and Installation
- Shock Absorber Suspension Without Trx
- Shock Absorber Suspension With Trx
Spring(S)
Removal and Installation
- Coil Spring
- Air Spring
- Trx
STABILIZER BAR, Rear Suspension
- Removal and InstallationRear Suspension Stabilizer Bar
TRACK BAR, Rear
Removal and Installation
- Rear Track Bar Without Trx
- Rear Track Bar With Trx
REMOVAL
| WARNING: |
All pressurized air suspension components contain high pressure air (up to 220 psig). Use extreme caution when inspecting for leaks. Wear safety goggles and adequate protective clothing when inspecting or servicing the air suspension system. A sudden release of air under this amount of pressure can cause possible serious or fatal injury. |
| WARNING: |
Before performing any service on the air suspension system, the system must be disabled to prevent the system from changing ride height. Before any given component is to be serviced it must be deflated. Servicing the air suspension system without the system disabled, or with pressure in any specific component, can cause possible serious or fatal injury. |
| CAUTION: |
When removing an air line from a component and the air line is to be reused, do not remove the 90° fitting or the brass fitting from the air line. If either is removed, the air line must be replaced. Do not remove protective caps or plugs from air lines or components until ready to install the air line to prevent moisture or dirt intrusion. All air line fittings must be hand started to avoid cross threading. |
| NOTE: |
The air suspension system can be disabled and enabled by using the Display Screen Module (DSM) in the vehicle under tire jack mode, which is the preferred method. If the disable level control routine in the scan tool is used it will only disable the level control (automatic and manual) for that ignition cycle. The air suspension system can also be enabled by driving the vehicle above 5 MPH. The air suspension should be disabled prior to lifting the vehicle or performing any work. |
- With a scan tool, using the routines under the Air Suspension Control Module (ASCM), perform the following:
- Raise and support the vehicle (Refer to 04 - Vehicle Quick Reference/Hoisting - Standard Procedure) .
- If equipped with a splash shield, remove the tire and wheel (Refer to 22 - Tires and Wheels/Removal and Installation) .
- If equipped remove the rear splash shield (Refer to 23 - Body/Exterior/SHIELD, Splash/Removal and Installation) .
- Support the axle with a suitable holding fixture.
- Disconnect the rear air line from the air spring.

1 - Air Spring Retainer Clip 2 - Rear Air Line - Lower the axle support and remove the air spring.

1 - Air Spring
INSTALLATION
Follow the removal procedure in reverse for general reassembly of the components on the vehicle. The steps listed below are calling out specific procedures that should be followed during installation.
- The rear air springs feature three serviceable upper retaining clips.
- Position the air spring to the frame and engage the upper retaining tabs in position.
- Carefully raise the rear axle until the air spring seats to the axle perch.
- Use the notch in the bottom of the rear air spring to orient the spring to the axle perch. The notch must face toward the front of the vehicle.
- With a scan tool, under the Air Suspension Control Module (ASCM), perform the following:
- Fill Spring From Reservoir: With a scan tool, using the routines under the Air Suspension Control Module (ASCM), perform the short fill routine three times on one rear air spring, checking the spring for proper engagement to axle and frame between each short fill command. Then perform a Complete Fill on that spring.
- Enable Level Control.
- Perform the ASCM Verification Test (Refer to 28 - DTC-Based Diagnostics/MODULE, Air Suspension Control (ASCM) - Standard Procedure) .