STARTING AND OPERATING
Parksense Front/Rear Park Assist System — If Equipped
▸Contents: RAM 1500 Owner's Manual
Getting To Know Your Vehicle
- Keys
- Sentry Key
- Ignition Switch
- Remote Start — If Equipped
- Vehicle Security System — If Equipped
- Doors
- Steering Wheel
- Driver Memory Settings — If Equipped
- Seats
- Uconnect Voice Recognition — If Equipped
- Driver Adjustable Pedals — If Equipped
- Mirrors
- Exterior Lights
- Interior Lights
- Windshield Wipers And Washers
- Climate Controls
- Interior Storage And Equipment
- Windows
- Power Sunroof — If Equipped
- Hood
- Tailgate
- Pickup Box
- Rambox — If Equipped
- Tri-Fold Tonneau Cover — If Equipped
Getting To Know Your Instrument Panel
- Midline Instrument Cluster — Gasoline
- Highline Instrument Cluster — Gasoline
- Premium Instrument Cluster — Gasoline
- Midline Instrument Cluster — Diesel
- Highline Instrument Cluster — Diesel
- Premium Instrument Cluster — Diesel
- Instrument Cluster Display
- Warning Lights And Messages
- Onboard Diagnostic System — Obd Ii
Starting And Operating
- Starting The Engine
- Engine Block Heater — If Equipped
- Engine Break-In Recommendations — Gasoline Engine
- Parking Brake
- Automatic Transmission
- Four-Wheel Drive Operation — If Equipped
- Active-Level Four Corner Air Suspension System — If Equipped
- Active-Level Four Corner Air Suspension System (Off-Road Group) — If Equipped
- Axle Lock System — If Equipped
- Limited-Slip Differential — If Equipped
- Power Steering
- Fuel Saver Technology 5.7l Engines Only — If Equipped
- Stop/Start System — If Equipped
- Cruise Control Systems — If Equipped
- Parksense Front/Rear Park Assist System — If Equipped
- Parksense Active Park Assist System — If Equipped
- Lanesense — If Equipped
- Parkview Rear Back Up Camera
- Surround View Camera System — If Equipped
- Trailer Cameras — If Equipped
- Refueling The Vehicle — Gasoline Engine
- Vehicle Loading
- Trailer Towing
- Snowplow
- Recreational Towing (Behind Motorhome)
- Driving Tips
Customer Assistance
The ParkSense Park Assist system provides visual and audible indications of the distance between the rear and/or front fascia/bumper and a detected obstacle when backing up or moving forward (e.g. during a parking maneuver). If your vehicle is equipped with the automatic braking function, the vehicle brakes may be automatically applied and released when the vehicle is in REVERSE if the system detects a possible collision with an obstacle.
The driver can disable the automatic braking function by turning ParkSense off via the ParkSense switch. The driver can also override automatic braking by changing the gear or by pressing the gas pedal over 90% of its capacity during the braking event.
Automatic brakes will not be available if the vehicle is in 4WD Low.
Automatic brakes will not be available if there is a fault in the brake module.
Automatic brakes will not be available if there is a faulted condition detected with the ParkSense Park Assist system or the Braking System.
The automatic braking function may only be applied if the vehicle deceleration is not enough to avoid colliding with a detected obstacle.
The automatic braking function may not be applied fast enough for obstacles that move toward the rear of the vehicle from the left and/or right sides.
The automatic braking function can be enabled/disabled from the Customer Programmable Features section of the Uconnect system.
ParkSense will retain its last known configuration state for the automatic braking function through ignition cycles.
Trailer hitch ball assembly may cause false braking events if left attached after towing.
The automatic braking function is intended to assist the driver in avoiding possible collisions with detected obstacles when backing up in REVERSE gear.
The system is designed to assist the driver and not to substitute the driver.
The driver must stay in full control of the vehicle's acceleration and braking and is responsible for the vehicle's movements.
For limitations of this system and usage precautions, see ParkSense System Usage Precautions.
ParkSense will retain the last system state (enabled or disabled) from the last ignition cycle when the ignition is placed in the ON/RUN position.
ParkSense can be active only when the gear selector is in REVERSE or DRIVE. If ParkSense is enabled while in one of these gears, the system will remain active until the vehicle speed is increased to approximately 7 mph (11 km/h) or above. A warning will appear in the instrument cluster display indicating the vehicle speed is above ParkSense operating speed while in REVERSE. The system will become active again if the vehicle speed is decreased to less than approximately 6 mph (9 km/h).