Diagnosis and Testing
Diagnosis And Testing - Speaker
▸Contents: 08 - Electrical
8A - Audio/Video/Entertainment/Connectivity
- Description And Operation
- Technical SpecificationsTorque Specifications
ANTENNA, Bluetooth/WiFi
Media Hub
Removal and Installation
SWITCH, Remote Radio
8B - Chime/Buzzer/Driver Assist
- DISPLAY, Blind SpotRemoval And Installation
MODULE, Park Assist
SENSOR, Blind Spot
SENSOR, Park Assist
Removal and Installation
8C - Power Accessories
Universal Transmitter
- DescriptionUniversal Garage Door Opener
- Diagnosis and TestingHomelink® Transceiver
Standard Procedure
- Erasing Homelink® Transceiver Codes
- Programming Homelink® Transceiver Codes
- Reprogramming Homelink® Transceiver Codes
- Removal And Installation
8E - Electronic Control Modules
- Standard ProcedureImmobilizer Components And Replacement Guide
- Technical SpecificationsTorque Specifications
Amplifier (Amp)
- Description and OperationAmplifier
- Removal and InstallationAmplifier (Amp)
Communication
- DescriptionDescription And Operation
CONNECTOR, Data Link (DLC)
- Description and OperationData Link Connector (Dlc)
CONTROL UNIT, DEF Heater
- Description
- Removal and InstallationDef Heater Control Unit
MODULE, Active Air Dam (AADM)
- DescriptionActive Air Dam (Aad) Module
- Removal and InstallationActive Air Dam Module
MODULE, Active Damping Control (ADCM)
- Description and OperationActive Damping Control Module (Adcm)
- Removal And Installation
MODULE, Active Noise Cancellation (ANC)
- Description and OperationActive Noise Cancellation (Anc) Module
Removal and Installation
- Microphone-Front
- Microphone-Rear
- Active Noise Cancellation Module
MODULE, Active Vibration Cancellation (AVCM)
- Description and OperationActive Vibration Cancellation (Avc)
Removal and Installation
- Actuator
- Module
- Module ProgrammingAvc Programming
MODULE, Adaptive Front Lighting System (AFLS)
- DescriptionAdaptive Front Lighting System (Afls)
- Removal and InstallationAdaptive Front Lighting System Module (Afls)
MODULE, Air Suspension Control (ASCM)
- Description and OperationAir Suspension Control Module (Ascm)
- Removal and InstallationAir Suspension Control Module (Ascm)
MODULE, Anti-Lock Brake System (ABS)
- Description And Operation
- Removal and InstallationAnti-Lock Brake System (Abs) Module
- Module ProgrammingAbs
MODULE, Blind Spot (BSM)
- Description and OperationBlind Spot Monitor (Bsm)
- Removal and InstallationBlind Spot Module (Bsm)
MODULE, Body Control (BCM)
- Description and OperationBody Control Module (Bcm)
- Removal and InstallationBody Control Module (Bcm)
MODULE, Central Vision Processing (CVPM)
- DescriptionDescription And Operation
- Removal and InstallationCentral Vision Processing Module (Cvpm)
- Module ProgrammingCvpm Programming
MODULE, Comfort Rear Seat (CRSM)
- Description and OperationComfort Rear Seat Module (Crsm)
- Removal and InstallationComfort Rear Seat Module (Crsm)
MODULE, Comfort Seat and Wheel (CSWM)
- Description and OperationComfort Seat Wheel Module (Cswm)
Removal and Installation
- Base
- Tungsten
MODULE, Display Screen (DSM)
Description and Operation
- Display Screen Module
- Front Passenger Display Module
Removal and Installation
- 8.4 Inch Display
- 12 Inch Display
- Front Passenger Display Module
MODULE, Door (DDM/PDM)
- Description and OperationDoor Control Modules
- Removal and InstallationDoor Control Module
MODULE, Drivers Assistance System (DASM)
- Description and OperationDrivers Assistance System Module (Dasm)
- Removal and InstallationDriver Assistance System Module (Dasm)
- Module ProgrammingDriver Assistance System Module (Dasm) Calibration
MODULE, Drivetrain Control (DTCM)
- Description and OperationDrivetrain Control Module (Dtcm)
- Removal and InstallationDrivetrain Control Module (Dtcm)
MODULE, Electric Power Steering (EPS)
- Description and OperationElectric Power Steering (Eps) Module
- Removal and InstallationElectronic Power Steering (Eps) Module
MODULE, Electronic Shift (ESM)
- Description and OperationElectronic Shift Module (Esm)
- Removal and InstallationElectronic Shift Module (Esm)
MODULE, Fuel Pump Control
- Description and OperationFuel Pump Control Module
- Removal and InstallationFuel Pump Control Module (Fpcm)
MODULE, Global Telematics Box
- Description and OperationGlobal Telematics Box Module (Tbm2)
Removal and Installation
- Module
- Backup Battery
Module, Hvac
- Description and OperationHvac System
- Removal and InstallationHvac Module
MODULE, Instrument Panel Cluster (IPC)
- Description And Operation
Removal and Installation
- Instrument Panel Cluster
- Mask And Lens
MODULE, Integrated Center Stack (ICSM)
- Description and OperationIntegrated Center Stack (Ics) Module
- Removal and InstallationIntegrated Center Stack Module (Icsm)
MODULE, Integrated Trailer Brake (ITBM)
- Description And Operation
- Diagnosis And Testing
Removal and Installation
- Integrated Trailer Brake Module (Itbm)
- Integrated Trailer Brake Switch (Itbs)
MODULE, Keyless Ignition Node (KIN)
- Description and OperationKeyless Ignition Node (Kin)
- Removal and InstallationKeyless Ignition Node (Kin)
MODULE, Memory Seat (MSM)
- Description and OperationMemory Seat Module (Msm)
Removal and Installation
- Base
- Tungsten
MODULE, Occupant Classification (OCM)
- Description and OperationOccupant Classification Module (Ocm)
- Removal and InstallationOccupant Classification Module (Ocm)
Controller, Occupant Restraint (ORC)
- Description and OperationOccupant Restraint Control (Orc)
- Removal and InstallationOccupant Restraint Controller (Orc)
MODULE, Park Assist (PAM)
- DescriptionDescription And Operation
- Removal and InstallationPark Assist Module
- Module ProgrammingDisable/Enable Park Assist Functionality
MODULE, Power Side Step (PSSM)
- Description and OperationPower Side-Step Module (Pssm)
- Removal and InstallationPower Side Step Module
MODULE, Powertrain Control (PCM)
- Description and OperationPowertrain Control Module (Pcm)
Removal and Installation
- Diesel
- GPEC 2a
- Gpec V
Module Programming
- Pcm Programming
- Tlc Learn Procedure
MODULE, Radio Frequency (RF Hub)
- Description and OperationRadio Frequency Hub (Rf-Hub)
- Removal and InstallationRadio Frequency (Rf Hub) Module
Module Programming
- Key Fob Programming
- Programming The Rf-Hub And Key Fobs
MODULE, Seat Massage (SMM)
- Description and OperationSeat Massage Module
- Removal and InstallationSeat Massage Module
MODULE, Security Gateway (SGW)
- Description and OperationSecurity Gateway (Sgw) Module
- Removal and InstallationSecurity Gateway (Sgw) Module
MODULE, Steering Column Control (SCCM)
- Description and OperationSteering Column Control Module (Sccm)
- Removal and InstallationSteering Column Control Module (Sccm)
MODULE, Trailer CAN Gateway Module (TCGWM)
- DescriptionTrailer Can Gateway Module
- Removal and InstallationTrailer Can Gateway Module (Tgwm)
MODULE, Trailer Interface (TIM)
- DescriptionTrailer Interface Module (Tim)
- Removal and InstallationTrailer Interface Module (Tim)
MODULE, Trailer Reverse Steering Control (TRSCM)
- DescriptionTrailer Reverse Steering Control (Trsc)
- Removal and InstallationTrailer Reverse Steering Control Module (Trscm)
MODULE, Trailer Surround View Camera Module (STIM)
- DescriptionTrailer Surround View Camera Module (Stim)
- Removal and InstallationTrailer Surround View Camera Module (Stim)
MODULE, Trailer Tire Pressure (TTPM)
- DescriptionTrailer Tire Pressure Monitoring (Ttpm)
- Removal and InstallationTrailer Tire Pressure Monitor (Ttpm)
MODULE, Transmission Control (TCM)
- Description and OperationTransmission Control Module (Tcm)
- Removal and InstallationTransmission Control Module
Module Programming
- Programming The Transmission Control Module
- Tcm Adaptation - 850re / 8hp75
Radio
- Description And Operation
Removal and Installation
- Radio With Dsm
- Radio Without Dsm
8F - Engine Systems
Battery System
- Description and OperationLow Voltage Battery System
Diagnosis and Testing
- Diagnosis And Testing - Single Battery 12 Volt System
- Open Circuit Voltage Test
Technical Specifications
- Battery
- Torque Specifications - Battery System
Standard Procedure
- Ignition Off Draw Test - Gas/Diesel
- 12 Volt Battery Charging
- BATTERY DISCONNECT AND CONNECT - eTORQUE SYSTEM
Battery
- Removal and InstallationBattery
SENSOR, Intelligent Battery (IBS)
- Removal and InstallationIntelligent Battery Sensor (Ibs)
TRAY, Battery
- Removal and InstallationBattery Tray - Except 6.2l
Starting
Description and Operation
- Standard Starting
- Remote Start System
- Diagnosis and TestingStandard Starting System
- Technical SpecificationsTorque Specifications
ANTENNA, Remote Start
- Removal and InstallationRemote Start Antenna (Rsa)
BUTTON, Start/Stop
- Removal and InstallationStart/Stop Button
Starter
- Removal and InstallationStarter Motor
8G - Heated/Cooled Systems
Heated/Cooled Accessories
- Description And Operation
Diagnosis and Testing
- Heated Steering Wheel
- Ventilated Seats
MOTOR, Vented Front Seat Back
Removal and Installation
- Vented Front Seat Back Motor
- Vented Front Seat Cushion Motor
- Vented Rear Seat Back Motor 40%
- Vented Rear Seat Back Motor 60%
- Vented Rear Seat Cushion Motor 40%
- Vented Rear Seat Cushion Motor 60%
PAD, Vented Front Seat Back
Removal and Installation
- Vented Front Seat Back Pad
- Vented Front Seat Cushion Pad
- Vented Rear Seat Back Pad 40%
- Vented Rear Seat Back Pad 60%
- Vented Rear Seat Cushion Pad 40%
- Vented Rear Seat Cushion Pad 60%
SWITCH, Heated Steering Wheel
- Removal and InstallationHeated Steering Wheel Switch
SWITCH, Vented Seat
Removal and Installation
- Removal And Installation
- Vented Rear Seat Switch
WHEEL, Heated Steering
- Removal and InstallationHeated Steering Wheel
Heated Glass
- Description And Operation
- Diagnosis and TestingDiagnosis And Testing - Electric Backlight (Ebl) And Heated Mirror System
GRID, Defogger
- Standard ProcedureStandard Procedure - Grid Line And Terminal Repair
- Heated MirrorsDescription And Operation
Heated Seats
- Description And Operation
- Diagnosis and TestingDiagnosis And Testing - Heated Seat System
PAD, Heater
Removal and Installation
- Base
- Tungsten
- Base
- Tungsten
- Heater Rear Seat Back Pad
- Heater Rear Seat Cushion Pad
SWITCH, Heated Seat
Removal and Installation
- Front Seat Switch
- In Center Seat
- In Floor Console
8H - Horn
- Description And Operation
- Diagnosis and TestingDiagnosis And Testing - Horn System
- Technical SpecificationsTorque Specifications
Horn
- Diagnosis and TestingDiagnosis And Testing - Horn
- Removal and InstallationHorn
SWITCH, Horn
- Diagnosis and TestingDiagnosis And Testing - Horn Switch
- Removal And Installation
8J - Instrument Cluster
- Description and OperationInstrument Cluster And Switches
- Diagnosis and TestingInstrument Panel Cluster
- Standard ProcedureEnhanced Seatbelt Reminder Programming
Removal and Installation
- Instrument Panel Cluster
- Mask And Lens
DISPLAY, Heads Up
- Removal and InstallationHeads Up Display
MODULE, Trailer Reverse Steering Knob (TRSKM)
- Removal and InstallationTrailer Reverse Steering Knob Module (Trskm)
POD, Switch Bank
- Removal and InstallationSwitch Bank Pod
SWITCH, EVIC Control
- Removal and InstallationEvic Switch
8L - Lamps and Lighting
Lamps/Lighting - Exterior
- Description and OperationExterior Lamps And Lighting
- Diagnosis and TestingExterior Lamps And Lighting
- Standard ProcedureFront Lamp Aiming
- Technical SpecificationsTorque Specifications
Lamp
- Removal and InstallationTrailer Hitch Lamp
LAMP, Cargo
- Removal and InstallationCargo Lamp
LAMP, Center High Mounted Stop
Removal and Installation
- Bulb
- Center High Mounted Stop Lamp (Chmsl)
LAMP, Fog
Removal and Installation
- Bulb
- Lamp - Bulb
- Front Fog Lamp
- Lamp - Rebel/Trx
- Lamp - Tungsten
LAMP, License Plate
- Removal and InstallationLicense Plate Lamp
LAMP, Mirror
Removal and Installation
- Puddle Lamp
- Puddle Lamp Power Telescoping
- Puddle Lamp Tow Mirror Without Surround View
- Puddle Lamp Tow Mirror With Surround View
- Signal Lamp
- Signal Lamp Power Telescoping
- Signal Lamp Tow Mirror
- Signature Lamp Power Telescoping
- Spotter Lamp Power Telescoping
- Spotter Lamp Trailer Towing
LAMP, Park and Turn Signal
- Removal and InstallationPark And Turn Signal Lamp
LAMP, Ram Box
- Removal and InstallationRam Box Lamp
LAMP, Identification
Removal and Installation
- Front
- Rear
LAMP, Side Marker, Front
- Removal and InstallationFront Side Marker Lamp
LAMP, Side Marker, Rear
- Removal and InstallationRear Side Marker Lamp
LAMP, Tail Stop Turn
Removal and Installation
- Bulb
- Tail Lamp Assembly
SENSOR, Stop Lamp
- Removal and InstallationStop Lamp Sensor
SWITCH, Headlamp
- Removal and InstallationHeadlamp Switch
- SWITCH, MultifunctionRemoval And Installation
UNIT, Front Lamp
- Standard ProcedureLamp Lens Defogging
Removal and Installation
- Headlamp Unit
- Headlamp Bulbs
Lamps/Lighting - Interior
- Description And Operation
- Diagnosis and TestingDiagnosis And Testing - Interior Lighting
LAMP, Courtesy
Removal and Installation
- Cupholder Overhead
- Console Lid
- Door Handle
- Door Map
- Door Mid Bin
- Footwell
- Instrument Panel
- Seat
LAMP, Glove Box
- Removal and InstallationLamp/Switch
LAMP, Dome
- Removal and InstallationDome Lamp
8N - Power Systems
Power Locks
- Description And Operation
- Diagnosis and TestingPower Locks
ANTENNA, Passive Entry
Removal and Installation
- Passive Entry Antenna - Center Cab
- Rear Cab
- Rear Door
- Rear Box
SWITCH, Lock
- Removal and InstallationLock Switch
- SWITCH, Tailgate ReleaseRemoval And Installation
TRANSMITTER, Integrated Key FOB
Diagnosis and Testing
- Keyfob Transmitter Battery
- Keyfob Transmitter
- Standard ProcedureKey Fob Programming
Power Mirrors
Description and Operation
- Exterior Power Mirrors
- Interior Power Mirrors
- MIRROR, Automatic Day and NightRemoval And Installation
MIRROR, Outside Rearview
- Removal and InstallationOutside Rearview Mirror
SWITCH, Mirror
- Diagnosis and TestingPower Mirror Switch
- Removal And Installation
Power Seats
Description and Operation
- Power Seats
- Memory Seats
- Diagnosis and TestingPower Seat System
MOTOR, Lumbar
- Removal and InstallationLumbar Motor
MOTOR, Seat
Removal and Installation
- Power Seat Motor
- Tungsten - Seat Cushion Extension
- Tungsten - Seat Fore-Aft
- Tungsten - Seat Tilt
- Tungsten - Seat Up-Down
SWITCH, Lumbar Control
- Removal and InstallationLumbar Control Switch
SWITCH, Memory
- Removal and InstallationMemory Switch
SWITCH, Seat, Power
Removal and Installation
- Base
- Tungsten
Power Side Step
- DescriptionPower Side Step
- Diagnosis and TestingDiagnosis And Testing - Power Side Steps
MOTOR, Power Side Step
- Removal and InstallationPower Side Step Motor
Power Tailgate
MODULE, Tailgate Control
- Removal and InstallationTailgate Control Module
Power Top, Sunroof
- Description And Operation
Diagnosis and Testing
- Diagnosis And Testing - Single Pane Power Sunroof System
- Diagnosis And Testing - Dual Pane Power Sunroof System
- Technical SpecificationsTorque Specifications
MOTOR, Sunroof
Standard Procedure
- Dual Pane Sunroof Calibrations
- Single Pane Sunroof Calibrations
- Sunroof Or Sunshade Obstacle Detection Override
Removal and Installation
- Dual Pane Motor
- Single Pane Motor
MOTOR, Sunroof Shade, Dual Pane
- Removal and InstallationDual Pane Sunroof Shade Motor
- SWITCH, SunroofRemoval And Installation
Power Windows
- Description and OperationPower Windows
- Diagnosis and TestingPower Windows
MOTOR, Window Regulator
- Removal and InstallationWindow Regulator Motor
SWITCH, Power Window
- Diagnosis and TestingDiagnosis And Testing - Power Window Switches
- Removal and InstallationPower Window Switch
8P - Speed Control
Description and Operation
- Conventional Cruise Control
- Adaptive Cruise Control With Stop And Go
SWITCH, Speed Control
- Removal and InstallationSpeed Control Switch
8Q - Vehicle Theft Security
Description and Operation
- Sentry Key Immobilizer System
- Vehicle Theft Alarm
- Diagnosis and TestingKey Fob Testing
SWITCH, Hood Ajar
- Diagnosis and TestingDiagnosis And Testing - Hood Ajar Switch
- Removal and InstallationHood Ajar Switch
8R - Wipers/Washers
- Description And Operation
- Diagnosis and TestingFront Wiper System
- Technical SpecificationsTorque Specifications
Cleaning
- Washer System Cleaning
- Wiper System Cleaning
Inspection
- Washer System Inspection
- Wiper System Inspection
ARM, Wiper
- Removal and InstallationWiper Arm
BLADE, Wiper
- Removal and InstallationWiper Blade
LINKAGE, Wiper Arm
- Removal and InstallationWiper Arm Linkage
MODULE, Humidity Rain Light Sensor
Standard Procedure
- Protective Cap Removal
- Silicone Gelatin Pad Replacement
- Removal and InstallationHumidity Rain Light Sensor Module (Hrlsm)
MOTOR, Wiper
- Removal and InstallationWiper Motor
NOZZLE, Washer
Removal and Installation
- Washer Nozzle
- Trx Washer Nozzle
PUMP, Windshield Washer
- Removal and InstallationWindshield Washer Pump
RESERVOIR, Windshield Washer
- Removal and InstallationWindshield Washer Reservoir
SWITCH, Multifunction, Left
- Removal and InstallationLeft Multifunction Switch
SWITCH, Washer Fluid Level
- Removal and InstallationWasher Fluid Level Switch
8T - Navigation/Telecommunication
Description and Operation
- Hands Free Phone
- Navigation
- Uconnect + Siriusxm Guardian
Diagnosis and Testing
- Diagnosis And Testing - Hands Free Phone
- Diagnosis And Testing - Navigation
- Diagnosis And Testing - Uconnect + Siriusxm Guardian
Standard Procedure
- Navigation System - Restore Or Update
- Uconnect + Siriusxm Guardian System - Reinstall Applications
- Uconnect® + Siriusxm® Guardian™ System - Remove Accounts
ANTENNA, Long-Term Evolution 2 (LTE2)
- Diagnosis and TestingDiagnosis And Testing - Cellular Antenna
- Removal and InstallationLong Term Evolution 2 (Lte2) Antenna
ANTENNA, Navigation
- Diagnosis and TestingDiagnosis And Testing - Navigation Antenna
- Removal and InstallationNavigation Antenna
Microphone
- Diagnosis and TestingDiagnosis And Testing - Microphone
- Removal and InstallationMicrophone
8W - Power Distribution
- Description And Operation
- Diagnosis and TestingWireless Charging Pad Module
- Technical SpecificationsTorque Specifications
CENTER, Power Distribution (PDC)
Removal and Installation
- Power Distribution Center - Front
- Power Distribution Center - Interior
MODULE, Power Inverter
- Removal and InstallationPower Inverter Module (Pim)
MODULE, Wireless Charging Pad
Removal and Installation
- Wireless Charging Pad Module
- Wireless Charging Pad Module-Trx
OUTLET, Power
- Diagnosis and TestingDiagnosis And Testing - 115 V Power Outlet
Removal and Installation
- 12 Volt Outlet – Instrument Panel
- 115 Volt Outlet – Front
- 115 Volt Outlet – Ram Box
- 115 Volt Outlet - Rear
- Switch – Rambox 115 Volt Outlet
- Usb Charge Port - Console Lid
- Usb Charge Port - Rear Console
SPEAKER RATTLE BUZZ AND SQUEAK
| WARNING: |
Disable the airbag system before attempting any steering wheel, steering column, seat belt tensioner, side airbag or instrument panel component diagnosis or service. Disconnect and isolate the negative battery (ground) cable. Wait two minutes for the airbag system capacitor to discharge before performing further diagnosis or service. This is the only sure way to disable the airbag system. Failure to follow these instructions may result in accidental airbag deployment and possible serious or fatal injury. |
| CAUTION: |
The speaker output of the radio is a “floating ground” system. Do not allow any speaker lead to short to ground, as damage to the radio may result. |
Any diagnosis of the Audio system should begin with duplicating the customer concern (verify the problem), include checking for applicable Technical Service Bulletins (TSB) and the use of a diagnostic scan tool. Check for any Diagnostic Trouble Code (DTC) data. If a DTC is found, refer to Section 28 - Radio and perform the appropriate diagnostic procedure before proceeding in this section. Refer to the appropriate wiring information.
Speaker Buzz, Squeak, Rattle (BSR) Diagnosis and Testing
Preconditions:
Test Procedure:
- Begin by verifying the customer complaint. The exact conditions that caused the issue for the customer must be used. Pay close attention to the following details:
- Read DTCs using diagnostic tool – If any Speaker related DTC present follow the DTC based diagnostic procedure.
- If no DTC present, confirm all the available interior SOL/service procedure is checked.
- Attempt to reproduce the issue in a non-radio mode, such as CD, Bluetooth®, or Auxiliary Input. This will help determine if it is a speaker issue or a reception issue.
- Once the complaint has been reproduced, clear the map pocket and storage bins of all loose items around the speaker in question.
- If the speaker noise is still present, visit the Tech Connect home page / Service Library Dashboard and follow the instructions to download the Audio Test Files for Speaker Diagnosis to a USB drive.

NOTE: The "Audio Test Files for Diagnosis" are available under "Reference Materials" section on main page of DealerCONNECT - Insert the USB drive in the proper input of the vehicle, and then set the following radio settings:
- Bass at +3 to +5,Balance/Fade (Toward the direction of the issue noted)
- Mid and treble at neutral
- Volume at step 30
- Based on location of the speaker at fault,use the following audio tests/files from table below.
Type of Speaker Test Audio Files Door Speakers 80Hz_audio_test_file.mp3 Front Dashboard IP Speakers Use The Tone Test (Appendix A) Headliner Speakers Use The Tone Test (Appendix A) Subwoofer 40Hz_audio_test_file.mp3 Soundbar 80Hz_audio_test_file.mp3
NOTE: If vehicle is not equipped with an external amplifier, skip Tone Test and use 80Hz_Audio_test_file.mp3.
NOTE: Use only the specified test audio for the speaker location. Using low-frequency (bass) test files on IP or headliner speakers may induce false trim or structure vibration and lead to incorrect speaker replacement. - Play all of the frequencies on the USB drive with the recommended settings. When a frequency reproduces the noise, press the interior panels around the speaker to see if the noise subsides. It may be necessary to replace broken trim clips or use foam tape to correct a speaker noise issue. Refer to the service manual for additional details.
Expected Result: Next Step/Pass-fail Criteria:NOTE: Increase volume gradually if not using the tone test. - Pass: Concern cannot be reproduced. Do NOT replace speaker. Return vehicle to customer or continue diagnosis only if additional symptoms are present.
- Fail: Noise Present Proceed to Enclosure & Trim Pressure Test
- Use the 40Hz, 80Hz audio test file or WiTECH tone test based on the speaker location defined in Table above.
- Keep Bass: +3 to +5, Balance/Fade: Towards the speaker exhibiting the issue.
- Depending on the location of the speaker, apply hand pressure to:
- Speaker grille area.
- Armrest.
- Switch bezel.
- Door handle trim.
- Headliner perimeter around speaker.
- Roof bow / cross-car beam area.
- Upper IP pad.
- Defroster grille.
- Adjacent trim seams.
- Subwoofer encloser.
- Adjacent trim panels.
- Seat frame / brackets.
- Floor or outer trim near enclosure.
- Loose/missing clips.
- Plastic-to-plastic contact.
- Vapor barrier interference.
- Headliner-to-roof bow contact.
- Loose retainers.
- Insufficient felt / foam isolation.
- IP pad to carrier interface.
- Grille looseness.
- Defroster duct contact.
- Harness / clip rattle.
- Trim contact points.
- Seat or bucket vibration.
- Enclosure contacting body.
SPEAKER DECOUPLING TEST
Test Procedure:
- Remover speaker fasteners.
- Pull speaker forward (keep connected).
- Replay heavy bass audio track or WiTECH tone test based on the speaker location defined in table above. Next Step / Pass-Fail Criteria: Pass: Noise disappears when speaker is decoupled. DO NOT REPLACE SPEAKER as is could be door structure or mounting issue. Check for:
Fail: If no change in noise observed Proceed to Speaker Comparison Test.
SPEAKER COMPARISON TEST (If available)
Purpose:
Test Procedure:
- Connect known-good speaker to same harness.
- Position speaker free-air (not mounted).
- Replay WiTECH tone test.
Next Step / Pass-Fail Criteria:
Pass: If the noise remains with known good speaker. It could be wiring/structure/mounting issue. DO NOT REPLACE SPEAKER
Fail: If the noise is not present with known good speaker, replace speaker.
OTHER POSSIBLE CAUSES
Check other areas like:
- Speaker wiring harness routing.
- Connector back-out.
- Ground Points.
- Seat frame or body cross-members.
- Shared fasteners between speaker and trim.
APPENDIX A: TONE TEST- AMPLIFIER TO SPEAKER CONNECTION VALIDATION
Purpose:
Confirm proper connection and functionality between amplifier output channels and corresponding vehicle speakers. This test is ONLY applicable to the vehicle equipped with the external amplifier.
Preconditions:
Test Procedure:
- Connect WiTech Tool to vehicle OBD port.
- Navigate to "Misc Functions" in the AMP from Topology page in Fig 2.
- Select the "AMP Tone Test" in the screen shown in Fig 3.

- In the screen shown in Fig 4, click the "Continue" button.

- In the dropdown menu shown in Fig. 5 select a channel and press continue. tone will be heard in that channel.

- If needed, tone test can be played in another channel. In the below screen Fig .6, select another channel to the tone test or "cancel" to exit.

- Confirm an audible test tone is heard from the corresponding speaker.
- Repeat Step 5 pf Appendix A for each individual output channel.
NOTE: Number of channels varies by amplifier variant (e.g, 17Ch Amp = 16 speaker channels + 1 sub/amp channel).
Electrical Diagnosis and Testing
- Turn the ignition switch to the ON position. Turn the radio receiver ON. Adjust the balance and fade controls to check the performance of each individual speaker. Note the speaker locations that are not performing correctly. Go to Step 2 .
NOTE: Subwoofer channel will not fade forward or rearward. Use the bass control to check the subwoofer channel output.
- Turn the radio receiver OFF. Turn the ignition switch to the OFF position. Disconnect and isolate the battery negative cable. Remove the radio receiver from the instrument panel. Disconnect the wire harness connector at the power amplifier. Check both the speaker feed (+) circuit and return (–) circuit cavities for the inoperative speaker location(s) at the radio receiver wire harness connectors for continuity to ground. In each case, there should be no continuity. If OK, go to Step 3 . If not OK, repair the shorted speaker feed (+) and or return (–) circuit(s) to the speaker as required.
- For each inoperative speaker location, check for continuity between the speaker feed (+) circuit cavities of the radio receiver wire harness connectors and the power amplifier wire harness connectors. Repeat the check for each inoperative speaker location between the speaker return (–) circuit cavities of the radio receiver wire harness connectors and the power amplifier wire harness connectors. In each case, there should be continuity. If OK, go to Step 4 . If not OK, repair the open speaker feed (+) and or return (–) circuit(s) as required.
- Check for continuity between the two ground circuit cavities of the power amplifier wire harness connector and a good ground. There should be continuity. If OK, go to Step 5 . If not OK, repair the open ground circuit(s) to ground as required.
- Install the radio receiver. Connect the battery negative cable. Check for battery voltage at the fused B(+) fuse for the power amplifier in the Power Distribution Center (PDC). If OK, go to Step 6 . If not OK, repair the open fused B(+) circuit to the PDC fuse as required.
- Check for battery voltage at the two fused B(+) circuit cavities of the power amplifier wire harness connector. If OK, go to Step 7 . If not OK, repair the open fused B(+) circuit(s) to the power amplifier fuse in the junction block as required.
- Turn the ignition switch to the ON position. Turn the radio receiver ON. Check for battery voltage at the enable signal to amplifier circuit cavity of the power amplifier wire harness connector. If OK, go to Step 8 . If not OK, repair the open enable signal to amplifier circuit to the radio receiver as required.
- Turn the radio receiver OFF. Turn the ignition switch to the OFF position. Disconnect and isolate the battery negative cable. For each inoperative speaker location, check both the amplified feed (+) circuit and the amplified return (–) circuit cavities of the power amplifier wire harness connectors for continuity to ground. In each case there should be no continuity. If OK, go to Step 9 . If not OK, repair the shorted amplified feed (+) and or amplified return (–) circuit(s) to the speaker as required.
- Disconnect the speaker wire harness connector at the inoperative speaker. Check for continuity between the amplified feed (+) circuit cavities of the speaker wire harness connector and the power amplifier wire harness connector. Repeat the check between the amplified return (–) circuit cavities of the speaker wire harness connector and the power amplifier wire harness connector. In each case there should be continuity. If OK, replace the faulty speaker. If not OK, repair the open amplified feed (+) and or amplified return (–) circuit(s) as required. If condition is still present, go to Step 10 .
- For each inoperative speaker location, check the resistance between the amplified feed (+) circuit and the amplified return (–) circuit cavities of the power amplifier wire harness connectors. The meter should read between 3 and 5 ohms (speaker resistance). If OK, replace the faulty power amplifier.