2023 Ram 1500

Position Statements

Repair Parts Used For Structural Repairs

▸Contents: 31 - Collision Information

This position statement supersedes any previously released “Structural Repair Parts Usage” position statements prior to December 01, 2025. Any previous version should be removed from your files. This is a complete revision and no asterisks have been added to highlight revisions.

FCA US LLC Position

FCA US LLC vehicles, systems and components are engineered, tested and manufactured to protect vehicle occupants based upon both government mandated and internal corporate requirements relative to durability, Noise/Vibration/Harshness (NVH), occupant protection and vehicle safety.

The overall structural integrity of the vehicle is dependent on its inherent design specifications. Sheet metal and glass are critical elements in the design of specific crush zones that allow the energy of a collision to be absorbed in a predictable way and maximize the effectiveness of the restraint system to protect the occupants. The use of parts not specifically designed and tested by FCA US LLC may compromise the integral balance between these safety systems.

Only Authentic Mopar® Repair Parts and glass are designed, engineered, manufactured and tested to the FCA US LLC internal and government mandated standards and are the only ones equivalent to the originally installed parts.

FCA US LLC does not approve of or recognize structural repair procedures where Authentic Mopar Parts are not used for Chrysler, Dodge, Jeep® and Ram vehicles. Any repairs performed not using Mopar parts, and not following published repair guidelines and procedures, may expose current or future vehicle owners and occupants to unnecessary risk.

When restoring a collision damaged vehicle to pre-loss condition, consideration must be given to the following:

  • All structural distortion has been identified and corrected using appropriate structural straightening equipment (“frame rack”) and a three-dimensional measuring system.
  • All damaged panels have been repaired or replaced.
  • All replaced panels provide the as-built structural equivalence and corrosion protection of the original panels.
  • Unless partial replacement procedures are documented in a FCA US LLC publication, structural panels must be installed in their entirety – partial replacement or “sectioning” of panels may compromise vehicle structure.
  • FCA US LLC strictly prohibits the collision repair process of “clipping”, the general practice of clipping would include the sectioning of multiple vehicles at the a-pillar, floor, rocker panel and other locations which contain advanced high strength steel reinforcements. These panels must be replaced at the factory seams when applicable. Risk of improper repair is significant and is not a supported practice.
  • FCA US LLC does not support the use or re-use of any structural component which has been removed from a vehicle previously damaged, flooded, burned, scrapped or removed from use for any other reason - commonly referred to as “salvage parts”.
  • While some salvage parts may “appear” equivalent, there can be dramatic differences in the design and functional characteristics which cannot be determined by a visual inspection and which could have a negative effect on the vehicle occupants in a future collision event.
  • Salvage components may have been affected by crash impact loads, incorrect, improper or inadequate disassembly and removal procedures, weathering or environmental exposure outside of that expected during normal use.
  • Salvage components are not traceable should a component recall be required in the future.
 

Genuine Mopar Parts

FCA US LLC vehicles and authentic Mopar Parts are designed and manufactured to meet production engineered specifications, while maximizing the safety of all occupants in a collision. If a collision repair is necessary, all repairs should be performed by a certified trained technician and follow vehicle-specific repair procedures available at TechAuthority.com using only genuine Mopar parts. Failure to follow proper procedures or deviation from Original Equipment parts could result in compromising performance of impact safety systems. Only authentic Mopar Parts are designed and built to provide optimum fit, function, safety and structural integrity as well as being engineered, manufactured and tested to the FCA US LLC internal and government-mandated standards and are the only parts equivalent to the originally installed parts. These parts are carefully designed to act as a safety system and are rigorously impact tested to ensure optimal performance.

Use of Aftermarket Parts

FCA US LLC does not approve of the use of aftermarket, third-party replacement parts, recycled, salvaged, aftermarket or reconditioned parts. Aftermarket parts are not subject to the same requirements of entire vehicle operation or function and may not be manufactured to the same standards or design. This could compromise the overall safety of the vehicle should a future collision occur. Aftermarket parts may not be built to FCA US LLC’s exact design and can therefore affect the performance of important structural and safety features of the vehicle.

This statement supersedes any previously released information by FCA US LLC.

Release Date: December 01, 2025

For more information, log on to https://www.MoparRepairConnection.com.

FCA US LLC vehicle lease agreements specify that ONLY Genuine FCA US LLC replacement parts be utilized for collision repairs to the vehicle.

©2026 FCA US LLC. All Rights Reserved. Chrysler, Dodge, Jeep, Ram, Mopar and SRT are registered trademarks of FCA US LLC. FIAT is a registered trademark of Fiat Group Marketing & Corporate Communication S.p.A., used under license by FCA US LLC.