2023 Ram 1500

Standard Procedure

Post Collision Scan Tool Inspection

▸Contents: 31 - Collision Information

Before any repair decisions are made, access to FCA US LLC service information is required. Diagnostic Trouble Codes (DTCs) do not identify which part needs to be replaced, rather DTCs are a piece of the diagnostic process that will lead a trained and qualified technician to the correct test to accurately diagnose the damage. Be certain of proper battery support when scanning.

Collision damage pre-scan before repairs- All vehicles that are in a collision need to have a diagnostic scan done at the beginning of the repair process, preferably during the estimating process, to determine damaged systems that may not be obvious. If proper battery support is not possible due to collision damage the scan should be performed during the repair process as soon as the battery can support the system and operate safely. After the repair process is completed the vehicle will need to be scanned again to be certain the systems involved are functioning properly. A Malfunction Indicator Light (MIL) may not illuminate for a particular system yet a DTC may be present, active or stored, compromising the proper function of the system. Identifying system faults will significantly reduce unexpected repairs at or near the end of the repair process. It will reduce the need for additional charges and benefit the vehicle being delivered without delay. The use of the Mopar scan tool wiTECH™ will be necessary to access DTC’s. and to perform many of the programming and initialization of modules. If the wiTECH™ scan tool is not available it can be obtained through an FCA US dealership service center. DTC identification is only part of the repair process as it will most likely be necessary to access the service and diagnostic information to understand proper operation, wiring and diagnosis and testing of the system and DTC.

The vehicle will also need to have a diagnostic scan done upon the completion of repairs to determine that all systems are functioning properly and if any of the systems are in need of repair, reprogramming or initialization.

Pre-Scan Process

  1. Conduct a customer consultation.

    1. Gain customer authorization to scan the vehicle and to share the data with the appropriate parties involved (sublet technician, insurer, repair facility personnel).
     
  2. Check for Malfunction Indicator Lamps (MILs) and/or information display messages.

    1. The 12-volt electrical system must be enabled to identify any MILs.
    2. Not all systems will illuminate MILs, even if there is damage to that system.
     
  3. Document any MILs and/or information display messages.
  4. Identify Driver Assistance Systems (DAS) which the vehicle is equipped with. These systems include but are not limited to Adaptive Cruise Control (ACC), Forward Collision Warning (FCW), Lane Sensing.
  5. Document the DAS the vehicle is equipped with.
  6. Document potential damage to DAS component(s), DAS mounting location(s), damage that may affect DAS , or parts that will need to be removed and installed near DAS.
  7. Identify any calibration, initialization and aiming requirements for DAS parts, including required calibration, initialization and aiming requirements following removal and installation.

    1. FCA US LLC service information as found on TechCONNECT
    2. Mopar TECH AUTHORITY
    3. RTS - OEM Calibration Requirements Search (https://rts.i-car.com/oem-calibration-requirements-search.html
     
  8. Identify enable and disable switches.

    1. The system may require enablement/disablement for calibration procedure.
    2. If the system is turned off, it may not be able to be calibrated.
    3. Systems that can be enabled or disabled should be documented, so that the system can be set to the customer’s preferences.
     
  9. Perform the pre-scan.

    1. A pre-scan is not possible if the 12-volt electrical system and vehicle communication networks are disabled or cannot be maintained throughout the scan.
    2. If the pre-scan is not possible due to vehicle damage, it should be done as soon as the repair progress allows it to be done safely.
     
  10. Document DTCs and other data.

    1. Does not include black box info, speed of accident/accident recreation.
    2. Include pending, current and past DTCs.
     
  11. Access the service information to identify system(s) affected by DTCs.

    1. Access the FCA vehicle specific service and diagnostic information.
    2. Check FCA vehicle specific information for service bulletins and recalls information that relate to DTCs.
     
  12. Determine likely related and unrelated DTCs.

    1. Key cycles/time stamps/freeze frame data.
     
 

Post Repair Calibrations and Post Scan Process

  1. Perform all required calibration/initialization/aiming steps, following the FCA service information procedures.

    1. Some systems will require the vehicle to be driven to perform calibration/initialization/aiming within the require driving parameters.
    2. Some systems will not detect issues within the system until the vehicle is driven within the required parameters.
    3. Some systems will require special tools and/or aiming equipment for calibration/initialization/aiming equipment
    4. Some systems will require both.
     
  2. Perform post-scan.
  3. If related DTC’s return, access the diagnostic information to troubleshoot the cause of the error.