2023 Ram 1500

Position Statements

Use Of Heat While Repairing Damaged Structural And Non-Structural Components

▸Contents: 31 - Collision Information

Structural Components:

Structural components are designed to help ensure occupant safety and structural integrity of the vehicle. If this type of component becomes damaged, it requires repair and/or replacement. Some repair methods may require damaged areas to be heated and “pulled” to relieve stress before disassembly.

If heat is used to straighten structural high-strength steels, advanced high-strength steel, or ultra high-strength steel, the component must be replaced. If the damaged component requires heat for making a pull, the adjacent component, to which it is attached, must not be affected by heat transfer. Cold straightening may be used without replacement of the component.

Heat produced by oxy-fuel cutting torches and other heating/cutting equipment has a negative effect on high-strength steels microstructure, making the affected steel incapable of meeting manufacturer requirements. Always validate the type of steel being repaired or replaced and follow the procedures required for welding and joining those steel strengths.

Some steels are unable to weld or may be difficult to weld using standard body shop equipment such as MIG/MAG welders and squeeze type resistant spot welders. Steels such as Press Hardened Steel (PHS), TRIP steel (TR, TRC), TRIP Assisted Bainitic steel (TB, TBC), or Quenching and Partitioning steel (QP, QPC), may present certain joining challenges. Refer to individual model repair procedures for joining/welding requirements.

Non-Structural Components:

Damaged non-structural mild steel components will require repair or replacement. Mild steel, in non-structural applications, can be repaired or replaced using common methods that apply heat or produce heat during the repair procedure.

Damaged non-structural mild steel components may require may require heat for the purpose of straightening the metal. If the damaged component requires heat for straightening, heat may be used to realign the component. If the mild steel component is attached to any type of high-strength steel component, heat must not transfer to the adjacent high-strength steel component.

Heat produced from stud welding guns, cut-off wheels, oxy-fuel torches and MIG welding operations, when used properly, is acceptable for use on mild steel, non-structural components. Always confirm the type of steel being repaired or replaced and verify heat application exclusions prior to attempting a repair.



NOTE:

Under no circumstances is a repair of any safety-related component acceptable. No cold straightening or heat-added reapir/replacement procedure may be used in proximity of a safety-related component including, but not limited to, restraint mounting areas, supplemental restraint mounting areas, occupant safety structure, impact safety, impact bars, intrusion beams, and roll-over protection. Ignoring these requirements will seriously compromise occupant safety in a future collision event, reduce the engineered qualities, and decrease durability and reliability of the vehicle.

Genuine Mopar Parts

FCA US LLC vehicles and authentic Mopar Parts are designed and manufactured to meet production engineered specifications, while maximizing the safety of all occupants in a collision. If a collision repair is necessary, all repairs should be performed by a certified trained technician and follow vehicle-specific repair procedures available at TechAuthority.com using only genuine Mopar parts. Failure to follow proper procedures or deviation from Original Equipment parts could result in compromising performance of impact safety systems. Only authentic Mopar Parts are designed and built to provide optimum fit, function, safety and structural integrity as well as being engineered, manufactured and tested to the FCA US LLC internal and government-mandated standards and are the only parts equivalent to the originally installed parts. These parts are carefully designed to act as a safety system and are rigorously impact tested to ensure optimal performance.

Use of Aftermarket Parts

FCA US LLC does not approve of the use of aftermarket, third-party replacement parts, recycled, salvaged, aftermarket or reconditioned parts. Aftermarket parts are not subject to the same requirements of entire vehicle operation or function and may not be manufactured to the same standards or design. This could compromise the overall safety of the vehicle should a future collision occur. Aftermarket parts may not be built to FCA US LLC’s exact design and can therefore affect the performance of important structural and safety features of the vehicle.

This statement supersedes any previously released information by FCA US LLC.

Release Date: December 01, 2025

FCA US LLC vehicle lease agreements specify that ONLY genuine Mopar replacement parts be utilized for collision repairs to the vehicle.

©2026 FCA US LLC. All Rights Reserved. Chrysler, Dodge, Jeep, Ram, Wagoneer, Mopar and SRT are registered trademarks of FCA US LLC. FIAT is a registered trademark of FCA Group Marketing S.p.A., used under license by FCA US LLC.