Removal and Installation
Steering Knuckle
▸Contents: 02 - Front Suspension
- Special Tools
Air Suspension
- Warning
- Description and OperationAir Suspension
- Diagnosis And Testing
Standard Procedure
- Technical SpecificationsTorque Specifications
Air Line
COMPRESSOR ASSEMBLY, Air Suspension
HOSE ASSEMBLY, Air Suspension
RESERVOIR, Air Suspension
SENSOR, Height
Removal and Installation
Front, Independent Front Suspension
- Description and OperationFront Suspension
Diagnosis and Testing
- Technical SpecificationsTorque Specifications
ARM, Lower Control
Removal and Installation
ARM, Upper Control
Removal and Installation
BALL JOINT, Suspension, Lower
BALL JOINT, Suspension, Upper
KNUCKLE, Steering
LINK, Stabilizer Bar
Removal and Installation
SHOCK ABSORBER, Suspension
Removal and Installation
SPRING, Front
Removal and Installation
STABILIZER BAR, Front
Wheel Alignment
REMOVAL
| NOTE: |
The air suspension system can be disabled and enabled by using the Display Screen Module (DSM) in the vehicle under tire jack mode, which is the preferred method. If the disable level control routine in the scan tool is used it will only disable the level control (automatic and manual) for that ignition cycle. The air suspension system can also be enabled by driving the vehicle above 8 km/h (5 mph). The air suspension should be disabled prior to lifting the vehicle or performing any work. |
- If equipped, disable the air suspension system.
- Raise and support the vehicle (Refer to 04 - Vehicle Quick Reference/Hoisting/Standard Procedure) .
- Remove the wheel and tire assembly (Refer to 22 - Tires and Wheels/Removal and Installation) .
- For TRX equipped vehicles remove the front wheel speed sensor routing bracket bolt.
1 - Speed Sensor Routing Bracket Bolt - Disconnect the outer tie rod end from the steering knuckle (Refer to 19 - Steering/Gear/TIE ROD, Steering/Removal and Installation) .
- Remove the brake rotor (Refer to 05 - Brakes, Base/Hydraulic/Mechanical/ROTOR, Brake,Front/Removal and Installation) .
- Disconnect the front wheel speed sensor from the hub and bearing (Refer to 05 - Brakes, ABS/Electrical/SENSOR, Wheel Speed, Front/Removal and Installation) .
- Remove the hub and bearing (Refer to 02 - Front Suspension/Front/HUB AND BEARING/Removal and Installation) .
- If equipped, remove the front halfshaft (Refer to 03 - Differential and Driveline/SHAFTS, Axle/Drive/Half/Removal and Installation) .
- Remove and DISCARD the lower ball joint nut.
1 - Upper Ball Joint Nut 2 - Nut 3 - Lower Ball Joint Nut - Remove and DISCARD the upper ball joint nut.
- Support the steering knuckle and separate the upper ball joint stud from the steering knuckle using the ball joint remover Remover, Ball Joint 8677 .
CAUTION: When installing puller to separate the ball joint, be careful not to damage the ball joint seal.
1 - Upper Ball Joint Stud 2 - Ball Joint Remover - Support the steering knuckle and separate the lower ball joint stud from the steering knuckle using ball joint remover Remover, Ball Joint 8677 .
1 - Lower Ball Joint Stud 2 - Ball Joint Remover - Remove the steering knuckle.
INSTALLATION
Follow the removal procedure in reverse for general reassembly of the components on the vehicle. The steps listed below are calling out specific procedures that should be followed during installation.
| CAUTION: | The ball joint stud taper must be CLEAN and DRY before installation into the steering knuckle. |
- Install a NEW upper ball joint nut and tighten to the proper (Torque Specifications) .
- Install a NEW lower ball joint nut and tighten to the proper (Torque Specifications) .
- Install the halfshaft nut (if equipped) and tighten to the proper (Torque Specifications) .
- For TRX equipped vehicles install the front wheel speed sensor routing bracket bolt and tighten to the proper (Torque Specifications) .
- Perform the wheel alignment standard procedure (Refer to 02 - Front Suspension/Wheel Alignment - Standard Procedure) .