Removal and Installation
Hydraulic Control Unit (Hcu) Without Trx
▸Contents: 05 - Brakes
05 - Brakes, ABS
- Description and OperationAnti-Lock Brake System (Abs)
- Standard ProcedureStandard Procedure - Antilock Brake System Bleeding
- Technical SpecificationsTorque Specifications
Electrical
SENSOR, Wheel Speed, Front
SENSOR, Wheel Speed, Rear
SWITCH, Electronic Stability Program (ESP)
Hydraulic/Mechanical
Integrated Control Unit (Icu)
Removal and Installation
Hydraulic Control Unit (Hcu)
Removal and Installation
05 - Brakes, Base
- Warning
- Caution
- DescriptionBase Brake System
- Diagnosis And Testing
- Standard ProcedureBrake System Bleeding
- Special Tools
Technical Specifications
Electrical
SWITCH, Brake Fluid Level
Removal and Installation
SWITCH, Adjustable Pedals
PUMP, Electric Vacuum
- SENSOR, Vacuum PressureRemoval And Installation
Hydraulic/Mechanical
ADAPTER, Disc Brake Caliper
Removal and Installation
CALIPER, Disc Brake, Front
CALIPER, Disc Brake, Rear
MASTER CYLINDER, Brake
PADS, Brake, Front
PADS, Brake, Rear
PEDAL(S), Brake and/or Accelerator
ROTOR, Brake
- Diagnosis and TestingDiagnosis And Testing - Disc Brake Rotor
Removal and Installation
Parking Brake
- Description And Operation
ACTUATOR, Electric Park Brake
SWITCH, Electric Park Brake
REMOVAL
- Disconnect and isolate the negative battery cable(s) (Refer to 08 - Electrical/Battery System/Standard Procedure) .
- Using a brake pedal holding tool, depress the brake pedal past its first inch of travel and hold it in this position. Holding the brake pedal in this position will isolate the master cylinder from the hydraulic brake system and will not allow brake fluid to drain out of the brake fluid reservoir while brake lines are open.
- Remove the Hydraulic Control Unit (HCU) inlet brake line flare nuts from the Hydraulic Control Unit (HCU).
1 - Wire Harness Connector 4 - ABS Module Fastener 2 - Flare Nut 5 - Flare Nut 3 - Flare Nut 6 - Bracket Bolt - Remove the Hydraulic Control Unit (HCU) outlet brake line flare nuts from the HCU.
NOTE: The Anti-Lock Brake System (ABS) module wire harness connector is cam-lock type and requires the red safety clip to be released for removal of the connector.
- Disconnect ABS module wire harness connector.
- Disengage the wire harness retainer from the Hydraulic Control Unit (HCU) bracket.
- Remove the Hydraulic Control Unit (HCU) bracket bolts.
- Remove the Integrated Control Unit (ICU) and Hydraulic Control Unit (HCU) bracket and as an assembly.
1 - HCU Bolts 2 - ABS Bolts - Remove the Hydraulic Control Unit (HCU) bolts and separate the ICU from the Hydraulic Control Unit (HCU) bracket.
- Remove the Anti-Lock Brake System (ABS) module bolts and separate the HCU from the ABS module.
INSTALLATION
Follow the removal procedure in reverse for general reassembly of the components on the vehicle. The steps listed below are calling out specific procedures that should be followed during installation.
- Install the Anti-Lock Brake System (ABS) module bolts and tighten to the proper (Torque Specifications) .
- Align the Integrated Control Unit (ICU) to the HCU bracket.
- Install the Hydraulic Control Unit (HCU) bolts and tighten to the proper (Torque Specifications) .
- Before connecting the ABS module wire harness connector to the ABS module, be sure the seal is properly installed in the connector.
- Position the HCU and HCU bracket assembly to the frame then install the Hydraulic Control Unit (HCU) bracket bolts and tighten to the proper (Torque Specifications) .
- Install the Hydraulic Control Unit (HCU) outlet brake line flare nuts to the HCU and tighten to the proper (Torque Specifications) .
- Install the Hydraulic Control Unit (HCU) inlet brake line flare nuts to the HCU and tighten to the proper (Torque Specifications) .
- Perform the ABS brake bleeding standard procedure (Refer to 05 - Brakes, ABS/Standard Procedure/ABS Brake Bleeding) .
- Perform the ABS initialization and clear any faults (Refer to 28 - DTC-Based Diagnostics/MODULE, Antilock Brake (ABS) /Standard Procedure) .