Diagnosis And Testing
05 - Brakes, Base
▸Contents: 05 - Brakes
05 - Brakes, ABS
- Description and OperationAnti-Lock Brake System (Abs)
- Standard ProcedureStandard Procedure - Antilock Brake System Bleeding
- Technical SpecificationsTorque Specifications
Electrical
SENSOR, Wheel Speed, Front
SENSOR, Wheel Speed, Rear
SWITCH, Electronic Stability Program (ESP)
Hydraulic/Mechanical
Integrated Control Unit (Icu)
Removal and Installation
Hydraulic Control Unit (Hcu)
Removal and Installation
05 - Brakes, Base
- Warning
- Caution
- DescriptionBase Brake System
- Diagnosis And Testing
- Standard ProcedureBrake System Bleeding
- Special Tools
Technical Specifications
Electrical
SWITCH, Brake Fluid Level
Removal and Installation
SWITCH, Adjustable Pedals
PUMP, Electric Vacuum
- SENSOR, Vacuum PressureRemoval And Installation
Hydraulic/Mechanical
ADAPTER, Disc Brake Caliper
Removal and Installation
CALIPER, Disc Brake, Front
CALIPER, Disc Brake, Rear
MASTER CYLINDER, Brake
PADS, Brake, Front
PADS, Brake, Rear
PEDAL(S), Brake and/or Accelerator
ROTOR, Brake
- Diagnosis and TestingDiagnosis And Testing - Disc Brake Rotor
Removal and Installation
Parking Brake
- Description And Operation
ACTUATOR, Electric Park Brake
SWITCH, Electric Park Brake
DIAGNOSIS AND TESTING – BRAKE ROTOR LOT ROT
If the vehicle has been on the lot for an extended period, the rotors may have a condition commonly referred to as lot rot. There may be a visible brake pad imprint on the friction surface, signs of corrosion, or both. This can lead to vibration or pulsation (shudder) while braking. The amount of time required to cause this varies and some vehicles are more sensitive than others. It is not always possible to tell visually if the vehicle exhibits lot rot, in part because the inboard rotor surface is hidden. It is best to perform a test drive, per the following procedure.
- Perform several brake applies from 80-48 km/h (50-30 mph) to clean off the rotors.
- Drive the vehicle on a smooth highway and, at 97 km/h (60 mph), apply the brake lightly such as when slowing down to exit the highway. Do this several times noting any vibration, either felt through the seat and body, or through the steering wheel.
- If steering wheel nibble or oscillation exists, that indicates the front rotors are likely the issue. If vibration is only felt through the seat and body, the rear rotors are likely the issue and less likely the front. A combination might indicate both front and rear rotors are an issue. Smooth braking indicates no issue.
- Resurface or replace front or rear rotors as necessary, per test drive, to resolve the vibration or pulsation (shudder) issue.
PRELIMINARY BRAKE CHECK
- Check the condition of the tires and wheels. Damaged wheels and worn, damaged, or underinflated tires can cause pull, shudder, vibration, and a condition similar to grab.
- If the complaint was based on noise while braking, inspect the suspension components. Jounce the front and rear of the vehicle and listen for noise that might be caused by loose, worn or damaged suspension or steering components.
- Inspect the brake fluid level and condition. Note that the brake reservoir fluid level will decrease in proportion to normal lining wear. Also note that brake fluid tends to darken over time. This is normal and should not be mistaken for contamination.
- If the fluid level is abnormally low, look for evidence of leaks at calipers, brake lines, Electronic Brake Booster (EBB), and Hydraulic Control Unit (HCU).
- If the fluid appears contaminated, drain out a sample to examine. System will have to be flushed if fluid is separated into layers, or contains a substance other than brake fluid. The system seals, hoses, EBB, and HCU will also have to be replaced after flushing. Use clean brake fluid to flush the system.
- Check the parking brake operation. Verify full release of both side rear brake calipers.
- Check the brake pedal operation. Verify that pedal does not bind and has adequate free play. If the pedal lacks free play, check the pedal and the EBB for being loose or for bind condition. Do not road test until condition is corrected.
- If the components checked appear OK, road test the vehicle.
ROAD TESTING
- If the concern involved low brake pedal, pump the pedal and note if it comes back up to normal height.
- Check the brake pedal response with the transmission in neutral and engine running. The pedal should remain firm under constant foot pressure.
- During the road test, make normal and firm brake stops in the 40-65 km/h (25-40 mph) range. Note problematic brake operation such as low pedal, hard pedal, fade, pedal pulsation, pull, grab, drag, noise, etc.
WHEEL AND TIRE PROBLEMS
Some conditions attributed to brake components may actually be caused by a wheel or tire problem.
A damaged wheel can cause shudder, vibration and pull. A worn or damaged tire can also cause pull.
| NOTE: |
Driveshaft angle can also cause vibration or shudder. |
Severely worn tires with very little tread left can produce a grab-like condition as the tire loses and recovers traction. Flat-spotted tires can cause vibration and generate shudder during brake operation. Tire damage such as a severe bruise, cut, ply separation, low air pressure can cause pull and vibration.
BRAKE LINING CONTAMINATION
Brake lining contamination is usually a product of leaking calipers or worn seals, driving through deep water puddles, or the lining has become covered with grease during repair. Contaminated lining should be replaced to avoid further brake problems.
BRAKES DO NOT HOLD AFTER DRIVING THROUGH DEEP WATER PUDDLES
This condition is generally caused by water-soaked linings. If the lining is only wet, it can be dried by driving and lightly applying and releasing the brakes for approximately one mile. Use caution while performing this to ensure you have enough clearance to other vehicles on the road or test area. However, if the lining is both soaked and dirt contaminated, cleaning and or replacement will be necessary.
BRAKE PULL
Front brake pull condition could result from:
- Contaminated lining in one caliper.
- Seized caliper piston.
- Binding caliper.
- Loose caliper.
- Rusty caliper slide surfaces.
- Damaged rotor.
- Wheel alignment (caster, camber, and toe out of specification).
- Tire pressure.
- Blocked or pinched brake hose.
- Blocked Anti-lock Brake System (ABS) orifice.
A worn and damaged wheel bearing or suspension component are further causes of pull. A damaged front tire (bruised, ply separation) can also cause pull.
A common and frequently misdiagnosed pull condition is where direction of pull changes after a few stops. The cause is a combination of brake drag followed by fade at one of the brake units.
As the dragging brake overheats, efficiency is so reduced that fade occurs. Since the opposite brake unit is still functioning normally, its braking effect is magnified. This causes pull to switch direction in favor of the normally functioning brake unit.
An additional point when diagnosing a change in pull condition concerns brake cool down. Remember that pull will return to the original direction, if the dragging brake unit is allowed to cool down (and is not seriously damaged).
BRAKE FADE
Brake fade is usually a product of overheating caused by brake drag. However, brake overheating and resulting fade can also be caused by riding the brake pedal, making repeated high deceleration stops in a short time span, or constant braking on steep mountain roads. Refer to the brake drag information in this section for causes.
BRAKE DRAG
Brake drag occurs when the lining is in constant contact with the rotor. Drag can occur at one wheel, all wheels, fronts only, or rears only.
Drag is a product of incomplete brake pad release. Drag can be minor or severe enough to overheat the linings, rotors, and park brake drums.
Minor drag will usually cause slight surface charring of the lining. It can also generate hard spots in rotors and park brake drums from the overheat-cool down process. In most cases, the rotors, wheels and tires are hot to the touch after the vehicle is stopped.
Severe drag can char the brake lining all the way through. It can also distort and score rotors to the point of replacement. The wheels, tires and brake components will be extremely hot. In severe cases, the lining may generate smoke as it chars from overheating.
Common causes of brake drag are:
- Parking brake partially applied.
- Loose or worn wheel bearing.
- Seized caliper.
- Caliper binding on corroded bushings or rusted slide surfaces.
- Loose caliper mounting.
- Mis-assembled components.
- Long booster output rod (Out of Spec Condition).
- Damaged brake pads.
- Damaged caliper abutment clips.
If brake drag occurs at the front, rear or all wheels, the problem may be related to a blocked master cylinder return port, faulty power booster (binds-does not release) or the Anti-lock Brake System (ABS).
PEDAL PULSATION
Pedal pulsation is caused by components that are loose, or beyond tolerance limits.
The primary cause of pulsation are disc brake rotors with excessive lateral runout or thickness variation, or out of round brake drums. Other causes are loose wheel bearings or calipers and worn, damaged tires.
| NOTE: |
Some pedal pulsation may be felt during Anti-lock Brake System (ABS) activation. |
HARD PEDAL OR HIGH PEDAL EFFORT
A hard pedal or high pedal effort may be due to an internal issue or blockage to the Electronic Brake Booster (EBB)
SPONGY PEDAL
A spongy pedal is most often caused by air in the system. However, substandard brake lines and hoses can also cause a spongy pedal. The proper course of action is to replace substandard quality brake hoses if suspected and bleed the system.
LOW PEDAL
If a low pedal is experienced, pump the pedal several times. If the pedal comes back up, the most likely causes are worn linings, rotors or calipers are not sliding on the slide pins. The proper course of action is to inspect and replace all worn component and make the proper adjustments.
PEDAL FALLS AWAY
A brake pedal that falls away under steady foot pressure is generally the result of a system leak or fluid contamination. The leak point could be at a brake line, hose or caliper. If leakage is severe, fluid will be evident at or around the leaking component.
Internal leakage in the Electronic Brake Booster (EBB) or Hydraulic Control Unit (HCU) may cause this with no physical evidence or visual fluid leak.
BRAKE NOISES
Some brake noise is common with rear brakes and on some disc brakes during the first few stops after a vehicle has been parked overnight or stored. This is primarily due to the formation of trace corrosion (light rust) on metal surfaces. This light corrosion is typically cleared from the metal surfaces after a few brake applications causing the noise to subside.
Unless evidence of a specific problem exists, rotor replacement is not generally required for an issue with brake noise.
BRAKE SQUEAK/SQUEAL/MOAN
Brake squeak or squeal may be due to linings that are wet or contaminated with brake fluid, grease, or oil. Glazed linings and rotors with hard spots can also contribute to squeak. Dirt and foreign material embedded in the brake lining will also cause squeak/squeal.
A very loud squeak or squeal is frequently a sign of severely worn brake lining. If the lining has worn through to the brake shoes in spots, metal-to-metal contact occurs. If the condition is allowed to continue, rotors may become so scored that replacement is necessary.
Humid morning conditions can cause moan until brakes heat and become dry.
| NOTE: |
The front and rear brake pads are equipped with wear indicators. The indicator will produce an audible noise when it contacts the rotor surface. Pad wear indicators produce a loud squeal noise to alert of worn out linings before metal to metal contact occurs. |
BRAKE CHATTER
Brake chatter is usually caused by loose or worn components, glazed or burnt linings could also be the cause. Rotors with hard spots can also contribute to chatter. Additional causes of chatter are out of tolerance rotors, loose wheel bearings and contaminated brake lining.
THUMP/CLUNK NOISE
Thumping or clunk noises during braking are frequently not caused by brake components. In many cases, such noises are caused by loose or damaged steering, suspension, or engine components. However, brake calipers that bind on the slide surfaces can generate a thump or clunk noise.
DIAGNOSIS AND TESTING - BASE BRAKE SYSTEM DIAGNOSIS CHARTS
| NOTE: |
There are three diagnosis charts that cover the RED BRAKE WARNING INDICATOR, BRAKE NOISE and OTHER BRAKE CONDITIONS. |
RED BRAKE WARNING INDICATOR
|
CONDITION |
POSSIBLE CAUSES |
CORRECTION |
|---|---|---|
|
RED BRAKE WARNING INDICATOR ON |
1. Parking brake not fully released. |
1. Check for Diagnostic Trouble Codes (DTC)s. |
|
2. Parking brake warning lamp circuit malfunction. |
2. Inspect the parking brake warning lamp circuit integrity and operation. |
|
|
3. Brake fluid level low in reservoir. |
3. Fill the brake fluid reservoir. Check entire system for leaks. Repair or replace as required. |
|
|
4. Brake fluid level switch. |
4. Disconnect the brake fluid level sensor wire harness connector. If the lamp goes out, replace switch. |
|
|
5. Instrument Panel Cluster (IPC) problem. |
5. Refer to the appropriate diagnostic information. |
|
|
6. Amber Anti-lock Brake System (ABS) Warning Indicator Lamp also illuminated. |
6. Refer to the appropriate diagnostic information. |
|
|
7. Electric park brake is not released (if equipped). |
7. Check the Electric Park Brake (EPB) switch position (if equipped). |
BRAKE NOISE
|
CONDITION |
POSSIBLE CAUSES |
CORRECTION |
|---|---|---|
|
CLICK OR SQUAWK ON PEDAL APPLICATION |
1. Brake pedal position sensor. |
1. Replace the brake pedal position sensor. Refer to the appropriate removal and installation information. |
|
2. Brake Transmission Shift Interlock Linkage (BTSI). |
2. Lubricate the BTSI linkage if equipped. |
|
|
3. Pedal pivot bushings. |
3. Replace the brake pedal. Refer to the appropriate removal and installation information. |
|
|
DISC BRAKE CHIRP |
1. Excessive brake rotor runout. |
1. Diagnose and replace as necessary. |
|
2. Lack of lubricant on brake caliper slides. |
2. Lubricate brake caliper slides. |
|
|
3. Caliper or shoes not fully seated. |
3. Reseat caliper or shoes. |
|
|
4. Inspect the linings for contamination. |
4. Remove the source of contamination. |
|
|
5. Coating worn on abutment. |
5. Replace the abutment clips. |
|
|
DISC BRAKE RATTLE OR CLUNK |
1. Broken or missing anti-rattle spring clips. |
1. Replace anti-rattle spring clips/shims and brake pads. |
|
2. Caliper guide pin bolts loose. |
2. Tighten guide pin bolts. |
|
|
SQUEAK/SQUEAL |
1. Brake shoe or pad linings. |
1. Replace brake shoes or pads. |
|
SCRAPING (METAL-TO-METAL) |
1. Foreign object interference with brakes. |
1. Inspect brakes and remove foreign object. |
|
2. Brake shoes or pads worn out. |
2. Replace the brake shoes or pads. Inspect the rotors. Reface or replace as necessary. |
|
|
3. Rock caught between the splash shield and the brake rotor. |
3. Remove the trapped rock(s). |
|
|
SCRAPING OR WHIRRING |
1. Wheel speed sensor hitting the tone wheel. |
1. Inspect, correct or replace the ineffective component(s). |
DIAGNOSIS AND TESTING - BRAKE FLUID CONTAMINATION
Indications of fluid contamination are swollen or deteriorated rubber parts.
Swollen rubber parts indicate the presence of petroleum in the brake fluid.
To test for contamination, put a small amount of drained brake fluid in clear glass jar. If fluid separates into layers, there is mineral oil or other fluid contamination of the brake fluid.
If brake fluid is contaminated, drain and thoroughly flush system. Replace the Electronic Brake Booster (EBB), Hydraulic Control Unit (HCU), caliper seals, wheel cylinder seals, and all hydraulic fluid hoses.
OTHER BRAKE CONDITIONS
|
CONDITION |
POSSIBLE CAUSES |
CORRECTION |
|---|---|---|
|
BRAKES CHATTER OR VIBRATION |
1. Brake rotor has excessive thickness variation. |
1. Isolate the condition as rear or front. Resurface or replace brake rotors as necessary. |
|
2. Uneven tire wear or wheel imbalance. |
2. Inspect the tires and wheels. Balance the wheels. |
|
|
BRAKES DRAG (FRONT OR ALL) |
1. Contaminated brake fluid. |
1. Check for swollen seals. Replace all system components containing rubber. |
|
2. Binding caliper pins or bushings. |
2. Replace the pins and bushings. |
|
|
3. Faulty Electronic Brake Booster (EBB). |
3. Inspect and replace EBB as necessary. |
|
|
4. Faulty Hydraulic Control Unit (HCU). |
4. Inspect and replace HCU as necessary. |
|
|
5. Binding brake pedal. |
5. Inspect and replace the brake pedal as necessary. |
|
|
BRAKES DRAG (REAR ONLY) |
1. Operator error. |
1. Describe the operation of the park brake. |
|
2. Park brake does not release. |
||
|
3. Electric Park Brake (EPB) caliper actuators (one or both) are not released. Or the EPB module or EPB actuators are not responding (If equipped). |
3. EPB module will set codes. |
|
|
BRAKES GRAB |
1. Contaminated brake pads or brake rotors. |
1. Inspect and clean or replace shoes/pads and rotors. Repair source of contamination. |
|
2. Improper brake booster assist. |
2. Refer to EBB in this section and scan for EBB related DTCs. |
|
|
3. Damaged wheel or tire. Wheel imbalance. |
3. Inspect the wheels and tires. Balance the wheels. |
|
|
EXCESSIVE PEDAL EFFORT |
1. Obstruction of brake pedal. |
1. Inspect and remove or move obstruction. |
|
2. Low brake booster assist. |
2. Refer to EBB in this section and scan for EBB related DTCs. |
|
|
3. Glazed brake linings. |
3. Reface or replace the brake rotors as necessary. Replace the brake pads. |
|
|
4. Brake pad lining transfer to brake rotor. |
4. Reface or replace the brake rotors as necessary. Replace the brake pads. |
|
|
EXCESSIVE PEDAL EFFORT (HARD PEDAL - CAN'T SKID WHEELS) |
1. Faulty EBB. |
1. Refer to EBB in this section and scan for EBB related DTCs. |
|
EXCESSIVE PEDAL TRAVEL (VEHICLE STOPS OK) |
1. Air in brake lines. |
1. Bleed brakes. |
|
2. Brake fluid low in reservoir. |
2. Fill the brake fluid reservoir. Check the entire system for leaks, repair or replace as required. |
|
|
EXCESSIVE PEDAL TRAVEL (ONE FRONT WHEEL LOCKS UP DURING HARD BRAKING) |
1. One of the two hydraulic circuits is malfunctioning. |
1. Inspect system for leaks. Check function of EBB and HCU and check for EBB and HCU related DTCs. |
|
PEDAL PULSATES OR SURGES DURING BRAKING |
1. Brake rotor has excessive thickness variation. |
1. Isolate condition as rear or front. Reface or replace brake rotors as necessary. |
|
2. Worn or damaged tires. |
2. Inspect the tires and wheels. |
|
|
3. Loose wheel bearings. |
3. Inspect the wheel bearings. |
|
|
4. Loose calipers. |
4. Inspect the brake calipers. |
|
|
5. Wheel imbalance. |
5. Balance the wheels. |
|
|
PEDAL IS SPONGY |
1. Air in the brake lines. |
1. Perform the brake bleed standard procedure. |
|
2. Faulty EBB. |
2. Refer to EBB in this section and scan for EBB related DTCs. |
|
|
PREMATURE REAR WHEEL LOCKUP |
1. Contaminated brake linings. |
1. Inspect and clean, or replace pads. Repair source of contamination. |
|
2. Anti-lock brake system function issue. |
2. Refer to the ABS section and appropriate diagnostic information. |
|
|
STOP LAMPS STAY ON |
1. Stop lamp sensor faulty. |
1. Inspect and replace the stop lamp sensor as necessary. |
|
2. Brake pedal binding. |
2. Inspect and replace as necessary. |
|
|
3. Obstruction in the pedal linkage. |
3. Remove the obstruction. |
|
|
4. Stop lamp sensor position not learned. |
4. Learn the stop lamp sensor using a scan tool. |
|
|
VEHICLE PULLS TO RIGHT OR LEFT ON BRAKING |
1. Seized brake caliper piston. |
1. Replace the seized piston or caliper and bleed the brakes. |
|
2. Contaminated brake pad lining (most likely front lining). |
2. Inspect and clean, or replace pads. Repair source of contamination. |
|
|
3. Pinched brake lines. |
3. Replace pinched line. |
|
|
4. Leaking piston seal. |
4. Replace piston seal or brake caliper. |
|
|
5. Suspension problem. |
5. Refer to the suspension section. |
|
|
6. Worn or damaged tires. |
6. Inspect the tires and wheels. |
|
|
7. Wheel imbalance. |
7. Balance the wheels. |