Diagnosis and Testing
Axle Diagnosis
▸Contents: 03 - Differential and Driveline
Description and Operation
Diagnosis and Testing
ASSEMBLY, Differential
Disassembly and Assembly
Actuator/Motor
GEAR, Ring and Pinion
Removal and Installation
Joints
SHAFTS, Axle/Drive/Half
Valves
Removal and Installation
Axle NVH issues are usually noise related. The most common source of noise from axles are either bearing or gear related. Many axle noises are vehicle speed sensitive. If the axle is equipped with a limited slip differential, vibration can be felt when a wheel speed difference is present when the vehicle is executing a turn.
Common items to check when an axle NVH issue is suspected:
- Check for proper fluid level. If vehicle is equipped with a friction style limited slip differential, make sure the correct fluid type is used and check for the need of a friction modifier. (Refer to 04 - Vehicle Quick Reference/Capacities and Recommended Fluids/Specifications) .
- Visually inspect the points of attachment of the axle to the chassis, especially any bushings that could be damaged or worn.
- Verify all fasteners attaching the axle to the chassis are present and properly torqued.
- Inspect the tires for proper inflation, unusual wear, properly balanced and being equally sized. Tire conditions that create noise or vibration can easily be mistaken for an axle issue.
- Check the pinion gear flange and axle hub flanges for damage. A dial indicator can be used to check the radial and axial runout if a bent component is suspected.
- A snap or clunk noise when the vehicle is shifted into gear, can be caused by:
- Road test the vehicle:
- Worn or damaged pinion bearings generally have a constant-pitch noise that changes only with vehicle speed.
- Worn or damaged differential bearings usually produce a low pitch noise and varies only with vehicle speed.
- Gear noise usually happens at a specific speed range. The noise can also occur during a specific type of driving condition. These conditions are acceleration, deceleration, coast, or constant load.
- Remove the differential cover and inspect the fluid as it is being drained for excess debris. Rotate the differential and visually inspect the gears for damage.
- Checking ring gear backlash and gear tooth contact pattern can usually be accomplished without any axle disassembly.
If any conditions are found that need correcting, refer to the appropriate Service Information for repair.
FLUID CHECK
Fill the axle to the bottom of the fill with the recommended fluid (Refer to 04 - Vehicle Quick Reference/Capacities and Recommended Fluids/Specifications) .
GEAR NOISE
Axle gear noise can be caused by insufficient lubricant, incorrect backlash, incorrect pinion depth, tooth contact, worn/damaged gears, or the carrier housing not having the proper offset and squareness.
Gear noise usually happens at a specific speed range. The noise can also occur during a specific type of driving condition. These conditions are acceleration, deceleration, coast, or constant load.
When road testing, first warm-up the axle fluid by driving the vehicle at least 5 miles and then accelerate the vehicle to the speed range where the noise is the greatest. Shift out-of-gear and coast through the peak-noise range. If the noise stops or changes greatly check for:
Differential side gears and pinions can be checked by turning the vehicle. The side gears are loaded during turns. They usually do not cause noise during straight-ahead driving when the gears are unloaded. A worn pinion shaft can also cause a snapping or a knocking noise.
BEARING NOISE
The axle shaft, differential and pinion bearings can all produce noise when worn or damaged. Bearing noise can be either a whining, or a growling sound.
Pinion bearings have a constant-pitch noise. This noise changes only with vehicle speed. Pinion bearing noise will be higher pitched because it rotates at a faster rate. Drive the vehicle and load the differential. If bearing noise occurs, the rear pinion bearing is the source of the noise. If the bearing noise is heard during a coast, the front pinion bearing is the source.
Differential bearings usually produce a low pitch noise. Differential bearing noise is similar to pinion bearing noise. The pitch of differential bearing noise is also constant and varies only with vehicle speed.
Axle shaft bearings produce noise and vibration when worn or damaged. The noise generally changes when the bearings are loaded. Road test the vehicle. Turn the vehicle sharply to the left and to the right. This will load the bearings and change the noise level. Where axle bearing damage is slight, the noise is usually not noticeable at speeds above 30 mph.
LOW SPEED KNOCK
Low speed knock is generally caused by:
VIBRATION
Vibration at the rear of the vehicle is usually caused by:
- Damaged drive shaft.
- Missing drive shaft balance weight(s).
- Worn or out-of-balance wheels.
- Loose wheel lug nuts.
- Worn U-joint(s).
- Loose/broken springs.
- Damaged axle shaft bearing(s).
- Loose pinion gear nut.
- Excessive pinion yoke run out.
- Bent axle shaft(s).
Check for loose or damaged front-end components or engine/transmission mounts. These components can contribute to what appears to be a rear end vibration. Do not overlook engine accessories, brackets and drive belts.
| NOTE: |
All driveline components should be examined before starting any repair. |
DRIVELINE SNAP
A snap or clunk noise when the vehicle is shifted into gear (or the clutch engaged), can be caused by:
- High engine idle speed.
- Transmission shift operation.
- Loose engine/transmission/transfer case mounts.
- Worn U-joints.
- Loose spring mounts.
- Loose pinion gear nut and yoke.
- Excessive ring gear backlash.
- Excessive side gear to case clearance.
The source of a snap or a clunk noise can be determined with the assistance of a helper. Raise the vehicle on a hoist with the wheels free to rotate. Instruct the helper to shift the transmission into gear and listen for the noise. A mechanics stethoscope is helpful in isolating the source of a noise.