Removal and Installation
C235 – Without Air Suspension
▸Contents: 03 - Differential and Driveline
Description and Operation
Diagnosis and Testing
ASSEMBLY, Differential
Disassembly and Assembly
Actuator/Motor
GEAR, Ring and Pinion
Removal and Installation
Joints
SHAFTS, Axle/Drive/Half
Valves
Removal and Installation
REMOVAL
- Disconnect and isolate the negative battery cable. If equipped with an Intelligent Battery Sensor (IBS), disconnect the IBS connector first before disconnecting the negative battery cable.
- Raise and support the vehicle (Refer to 04 - Vehicle Quick Reference/Hoisting - Standard Procedure) .
- Remove both rear wheels (Refer to 22 - Tires and Wheels/Removal and Installation) .
- Disconnect both rear wheel speed sensor wire harness connectors. (Air suspension shown, Coil suspension rear wheel speed sensor wire harness connector location and bracket location identical.)
1 – Rear Brake Hose Routing Bracket Bolt 2 – Rear Wheel Speed Sensor Wire Harness Connector - Remove both rear caliper adapters (Refer to 05 - Brakes, Base/Hydraulic/Mechanical/ADAPTER, Disc Brake Caliper/Installation) .
- Loosen the clamp and disconnect the axle vent hose from the axle.
1 – Vent Hose - Remove the rear driveshaft (Refer to 03 - Differential and Driveline/SHAFTS, Axle/Drive/Half/Removal and Installation) .
- Remove and DISCARD the upper control arm bracket bolts and nuts and position the upper control arms aside away from the axle.
1 – Upper Control Arms 2 – Upper Control Arm Bolts And Nuts At Axle - Remove the stabilizer bar bolts, the stabilizer bar brackets and position aside the stabilizer bar.
1 – Stabilizer Bar Bolts 2 – Stabilizer Bar Brackets - Position a lift under the axle and secure the axle to the lift.
- Remove and DISCARD the track bar axle bolt.
1 – Track Bar Frame Bolt 2 – Track Bar Axle Bolt - Remove both lower shock absorber bolts and nuts and position the shock absorbers away from the axle.
1 – Lower Shock Absorber Bolts And Nuts 2 – Shock Absorber - Remove and DISCARD the lower control arm bolts and nuts and position the lower control arms away from the rear axle.
1 – Lower Control Arm Bolts And Nuts 2 – Lower Control Arm - If equipped with coil springs, slightly lower the rear axle assembly and remove the rear coil springs.
1 – Rear Axle Assembly 2 – Coil Springs - Remove the rear axle from the vehicle.
INSTALLATION
| NOTE: |
All suspension torques should be made with the full vehicle weight on the ground being supported by the tires. |
- Position the coil springs in place on the rear axle and align into the spring upper pocket.
- Carefully raise the rear axle in place.
1 – Rear Axle Assembly 2 – Coil Springs - Position both the lower control arms into the rear axle brackets and loosely install the NEW lower control arm bolts and nuts.
1 – Lower Control Arm Bolts And Nuts 2 – Lower Control Arm - Position both the upper control arms in the rear axle brackets and loosely install the NEW upper control arm bolts and nuts.
1 – Upper Control Arms 2 – Upper Control Arm Bolts And Nuts At Axle - Position both the rear shock absorbers in the axle brackets and loosely install the rear shock absorber bolts and nuts.
1 – Lower Shock Absorber Bolts And Nuts 2 – Shock Absorber - Position the track bar on the axle and loosely install the NEW the track bar axle bolt.
1 – Track Bar Frame Bolt 2 – Track Bar Axle Bolt - Remove the axle lift.
NOTE: The stabilizer bar must be centered with equal spacing on both sides.
- Position the stabilizer bar in position and install the stabilizer brackets to the rear axle, install the rear stabilizer bolts to the proper (Torque Specifications) .
1 – Stabilizer Bar Bolts 2 – Stabilizer Bar Brackets - Connect the axle vent hose to the axle and install the clamp.
1 – Vent Hose - Install the both rear caliper adapters (Refer to 05 - Brakes, Base/Hydraulic/Mechanical/ADAPTER, Disc Brake Caliper/Installation) .
- Connect the rear wheel speed sensor wire harness connectors.
1 – Rear Brake Hose Routing Bracket Bolt 2 – Rear Wheel Speed Sensor Wire Harness Connector - Fill the axle with the specified lubricant to the proper level (Refer to 04 - Vehicle Quick Reference/Capacities and Recommended Fluids/Specifications) .
- Install the rear driveshaft (Refer to 03 - Differential and Driveline/SHAFTS, Axle/Drive/Half/Removal and Installation) .
- Install the rear wheels (Refer to 22 - Tires and Wheels/Removal and Installation) .
- Remove the supports and lower the vehicle to properly load the suspension.
- Tighten the upper control arm bolts and nuts.
1 – Upper Control Arms 2 – Upper Control Arm Bolts And Nuts At Axle - Tighten the lower control arm bolts and nuts.
1 – Lower Control Arm Bolts And Nuts 2 – Lower Control Arms - Tighten the track bar axle bolt.
1 – Track Bar Frame Bolt 2 – Track Bar Axle Bolt - Tighten the shock bolts and nuts.
1 – Lower Shock Absorber Bolts And Nuts 2 – Shock Absorber - Connect the negative battery cable. If equipped with an Intelligent Battery Sensor (IBS), connect the IBS connector.
TORQUE SPECIFICATIONS - C235 DIFFERENTIAL