The following Repair Procedures and Torque Specifications will cover the removal and installation of the left and right axle seals.
REMOVAL
- Raise and support the vehicle (Refer to 04 - Vehicle Quick Reference/Hoisting/Standard Procedure) .
- Remove the left halfshaft (Refer to 03 - Differential and Driveline/SHAFTS, Axle/Drive/Half/Removal and Installation) .
- Clean the axle seal area of any dirt or debris.
- Remove the O-ring and snap ring from the axle shaft.
 |
|
| 1 - O-Ring |
| 2 - Snap Ring |
| 3 - Axle Shaft |
- Remove the axle shaft using the Remover, Shaft 8420B and Slide Hammers C-3752 .
 |
|
| 1 - Axle Shaft |
| 2, 3, 4 - Axle Shaft Remover Tool |
- Remove the axle shaft seal.
 |
|
| 1 - Axle Shaft |
| 2 - Oil Slinger |
- Remove and DISCARD the oil slinger from shaft.
INSTALLATION
Follow the removal procedure in reverse for general reassembly of the components on the vehicle. The steps listed below are calling out specific procedures that should be followed during installation.
TORQUE SPECIFICATIONS - 215FD FRONT AXLE
DRAIN PLUG, FILL PLUG FRONT AXLE DISCONNECT, FRONT AXLE TUBE, FRONT AXLE MOUNTS
|
CALLOUT
|
DESCRIPTION
|
SPECIFICATION
|
COMMENT
|
|
1
|
Front Axle Disconnect(FAD) Actuator Bolts
|
28 N⋅m (21 Ft. Lbs.) |
–
|
|
2
|
Fill Plug
|
35 N⋅m (26 Ft. Lbs.) |
–
|
|
3
|
Drain Plug
|
35 N⋅m (26 Ft. Lbs.) |
–
|
DIFFERENTIAL MOUNT BRACKET AND PINION BRACKET
|
CALLOUT
|
DESCRIPTION
|
SPECIFICATION
|
COMMENT
|
|
1
|
Differential Mount Bracket to Engine Block
|
63 N·m (46 Ft. Lbs.) |
These bolts also go through the left engine mount bracket
|
|
2
|
Differential Mount Bracket to Engine
|
63 N·m (46 Ft. Lbs.) |
–
|
|
3
|
Differential Mount Bracket to Pinion Mount Bracket
|
80 N·m (59 Ft. Lbs.) |
–
|
|
4
|
Pinion Mount Bracket to Differential
|
110 N·m (81 Ft. Lbs.) |
–
|
|
CALLOUT
|
DESCRIPTION
|
SPECIFICATION
|
COMMENT
|
|
1
|
Engine Front Support to Axle RH
|
110 N⋅m (81 Ft. Lbs.) |
–
|
|
2
|
Engine Front Support to Axle LH
|
110 N⋅m (81 Ft. Lbs.) |
–
|
REMOVAL
- Raise and support the vehicle (Refer to 04 - Vehicle Quick Reference/Hoisting/Standard Procedure) .
- Remove the right halfshaft (Refer to 03 - Differential and Driveline/SHAFTS, Axle/Drive/Half/Removal and Installation) .
- Remove and DISCARD the snap ring and O-ring from the output shaft.
 |
|
| 1 - Snap Ring |
| 2 - O-Ring |
| 3 - Oil Slinger |
- Remove and DISCARD the oil slinger.
- Remove and DISCARD the axle seal from the axle tube.
 |
|
| 1 - Axle Seal |
| 2 - Axle Tube |
INSTALLATION
Follow the removal procedure in reverse for general reassembly of the components on the vehicle. The steps listed below are calling out specific procedures that should be followed during installation.
TORQUE SPECIFICATIONS - 215FD FRONT AXLE
DRAIN PLUG, FILL PLUG FRONT AXLE DISCONNECT, FRONT AXLE TUBE, FRONT AXLE MOUNTS
|
CALLOUT
|
DESCRIPTION
|
SPECIFICATION
|
COMMENT
|
|
1
|
Front Axle Disconnect(FAD) Actuator Bolts
|
28 N⋅m (21 Ft. Lbs.) |
–
|
|
2
|
Fill Plug
|
35 N⋅m (26 Ft. Lbs.) |
–
|
|
3
|
Drain Plug
|
35 N⋅m (26 Ft. Lbs.) |
–
|
DIFFERENTIAL MOUNT BRACKET AND PINION BRACKET
|
CALLOUT
|
DESCRIPTION
|
SPECIFICATION
|
COMMENT
|
|
1
|
Differential Mount Bracket to Engine Block
|
63 N·m (46 Ft. Lbs.) |
These bolts also go through the left engine mount bracket
|
|
2
|
Differential Mount Bracket to Engine
|
63 N·m (46 Ft. Lbs.) |
–
|
|
3
|
Differential Mount Bracket to Pinion Mount Bracket
|
80 N·m (59 Ft. Lbs.) |
–
|
|
4
|
Pinion Mount Bracket to Differential
|
110 N·m (81 Ft. Lbs.) |
–
|
|
CALLOUT
|
DESCRIPTION
|
SPECIFICATION
|
COMMENT
|
|
1
|
Engine Front Support to Axle RH
|
110 N⋅m (81 Ft. Lbs.) |
–
|
|
2
|
Engine Front Support to Axle LH
|
110 N⋅m (81 Ft. Lbs.) |
–
|
TORQUE SPECIFICATIONS - BRAKES BASE
|
DESCRIPTION
|
SPECIFICATION
|
COMMENT
|
|
Brake Booster Nuts
|
32 N·m (24 Ft. Lbs.) |
Do not reuse these fasteners. If removed, a new fastener must be installed and tightened to specifications.
|
|
Brake Line Front Hose Flare Nut
|
18 N·m (13 Ft. Lbs.) |
–
|
|
Brake Vacuum Pump Bracket
|
23 N·m (17 Ft. Lbs.) |
–
|
|
Brake Vacuum Pump
|
7 N·m (62 In. Lbs.) |
–
|
|
Brake Vacuum Line Fasteners
|
8 N·m (71 In. Lbs.) |
–
|
|
Caliper Bleed Screws
|
19 N·m (14 Ft. Lbs.) |
–
|
|
Electric Park Brake (EPB) Actuator Bolts
|
12 N·m (9 Ft. Lbs.) |
–
|
|
Front Brake Rotor Bolt
|
10 N·m (7 Ft. Lbs.) |
–
|
|
Front Brake Hose Banjo Bolt
|
35 N·m (26 Ft. Lbs.) |
–
|
|
Front Brake Hose Bolt
|
12 N·m (9 Ft. Lbs.) |
–
|
|
Front Caliper Adapter Bolts
|
80 + 55° N·m (59 + 55° Ft. Lbs.) |
Do not reuse these fasteners. If removed, a new fastener must be installed and tightened to specifications.
|
|
Front Caliper Bolts
|
75 N·m (55 Ft. Lbs.) |
–
|
|
Front Junction Block Brake Line Flare Nut
|
22 N·m (16 Ft. Lbs.) |
–
|
|
Front and Rear Brake Hose to Bracket Bolt
|
20 N·m (15 Ft. Lbs.) |
–
|
|
Hydraulic Control Unit (HCU) Inlet Brake Line Flare Nuts
|
25 N·m (18 Ft. Lbs.) |
–
|
|
Hydraulic Control Unit (HCU) Outlet Brake Line Flare Nuts
|
22 N·m (16 Ft. Lbs.) |
–
|
|
Master Cylinder Brake Line Flare Nuts
|
23 N·m (17 Ft. Lbs.) |
–
|
|
Master Cylinder Nuts
|
23 N·m (17 Ft. Lbs.) |
Do not reuse these fasteners. If removed, a new fastener must be installed and tightened to specifications.
|
|
Pedal Sled Nuts
|
32 N·m (24 Ft. Lbs.) |
Do not reuse these fasteners. If removed, a new fastener must be installed and tightened to specifications.
|
|
Rear Brake Hose Banjo Bolt
|
35 N·m (26 Ft. Lbs.) |
–
|
|
Rear Brake Hose Junction Block
|
21 N·m (15 Ft. Lbs.) |
–
|
|
Rear Brake Tube to Junction Block Nut
|
17 N·m (13 Ft. Lbs.) |
–
|
|
Rear Brake Line Junction Block Flare Nut
|
22 N·m (16 Ft. Lbs.) |
–
|
|
Rear Brake Rotor Bolt
|
20 N·m (15 Ft. Lbs.) |
–
|
|
Rear Brake Rotor Splash Shield Bolts
|
11 N·m (8 Ft. Lbs.) |
–
|
|
Rear Caliper Bolts
|
35 N·m (26 Ft. Lbs.) |
–
|
|
Rear Caliper Adapter Bolts
|
100 N·m (74 Ft. Lbs.) |
Do not reuse these fasteners. If removed, a new fastener must be installed and tightened to specifications.
|
|
Rear Junction Block Bolt
|
18 N·m (13 Ft. Lbs.) |
–
|
|
Rear Junction Block Brake Line Flare Nut - 2019 to 2020
|
22 N·m (16 Ft. Lbs.) |
–
|
|
Rear Junction Block Brake Line Flare Nut - 2021 and forward
|
21 N·m (15 Ft. Lbs.) |
–
|
TORQUE SPECIFICATIONS - WHEEL LUG NUT
|
CALLOUT
|
DESCRIPTION
|
SPECIFICATION
|
LUG NUT SIZE
|
LUG NUT SOCKET SIZE
|
COMMENT
|
|
1
|
Lug Nut
|
176 N·m (130 Ft. Lbs.)
|
M14 x 1.50
|
22 mm
|
Use only authorized dealer recommended lug nuts and clean or remove any dirt or oil before tightening.
|