2023 Ram 1500

Removal and Installation

Ring And Pinion Gear - C235

▸Contents: 03 - Differential and Driveline

REMOVAL



NOTE:

The ring gear and pinion are serviced in a matched set. Never replace one gear without replacing the other matching gear.

  1. Remove the differential from the differential housing (Refer to 03 - Differential and Driveline/ASSEMBLY, Differential/Removal and Installation) .
  2. Place the differential case in a vise with soft metal jaw protectors.
  3. Remove the ring gear bolts from the differential case and DISCARD .

    1 – Ring Gear Bolts

  4. Drive the ring gear off the differential case using a drift punch or soft hammer.

    NOTE: If using a drift punch, take care not to hit the threads on the ring gear or damage may occur.

    1 – Drift Punch
    2 – Ring Gear
  5. Install the bolts into two of the threaded holes in the companion flange 180° apart.
  6. Position Holder, Yoke 6719A against the companion flange and install a bolt and washer into one of the remaining threaded holes. Tighten the bolts so the yoke holder is held to the flange.
  7. Remove the companion flange nut.
  8. Place an alignment mark on the companion flange to pinion shaft.
  9. Remove the companion flange using Puller, Companion Flange C-452 .

    1 – Puller, Companion Flange C-452
    2 – Companion Flange

  10. Remove pinion gear from the housing with Pinion Driver 8976 and a hammer.

    1 – Pinion Gear
    2 – Pinion Driver 8977A

  11. Remove the pinion seal using a small chisel or seal puller.

    1 – Chisel
    2 – Pinion Seal

  12. Remove the front pinion bearing.

    1 – Front Pinion Bearing
    2 – Front Pinion Bearing Cup

  13. Remove the front pinion bearing cup using a drift punch.

    1 – Drift Punch
    2 – Front Pinion Bearing Cup

  14. Remove the rear pinion bearing cup from the housing using a drift punch.

    1 – Drift Punch
    2 – Rear Pinion Bearing Cup

  15. Remove the pinion depth shim from behind the bearing cup bore and record the shim thickness.

    1 – Pinion Depth Shim
    2 – Bearing Cup Bore

  16. Remove the collapsible spacer from the pinion shaft.

    1 – Collapsible Spacer
    2 – Pinion Shaft

  17. Remove the rear pinion bearing from the pinion shaft using bearing separator and a press or using Puller, Press C-293-PA and Block Set, Puller C-293-37 .

    1 – Puller, Press C-293-Pa With Block Set, Puller C-293-37
    2 – Rear Pinion Bearing
    3 – Pinion Shaft

 

INSTALLATION


NOTE:

The ring gear and pinion gear are serviced as a matched set. Do not replace one gear without replacing the other matched gear. If the ring and pinion gears or bearings are replaced refer to (Refer to 03 - Differential and Driveline/Adjustments) for Pinion Gear Depth Setting. Do not reuse the bearings.

  1. Install the pinion depth shim.

    1 – Pinion Depth Shim
    2 – Bearing Cup Bore

  2. Install a NEW rear pinion bearing cup.

    1 – Rear Pinion Bearing Cup
    2 – Pinion Depth Shim

  3. Using Installer, Bearing Cup D-111 and Driver Handle, Universal C-4171 . fully seat the bearing cup in the pinion housing.

    1 – Installer, Bearing D-111 With Driver Handle, Universal C-4171

  4. Install a NEW front pinion bearing cup.

    1 – Front Pinion Bearing Cup
    2 – Front Pinion Bearing Cup Bore

  5. Using Installer, Bearing Cup D-129 and Driver Handle, Universal C-4171 , fully seat the bearing cup in the pinion housing.

    1 – Installer, Bearing Cup D-129 With Driver Handle, Universal C-4171

  6. Install a NEW front pinion bearing into the housing.

    1 – Front Pinion Bearing
    2 – Front Pinion Bearing Cup

  7. Install a NEW pinion seal using Installer, Seal C-4076-B and Handle, Driver C-4735 .

    1 – Installer, Seal C-4076-B With Handle, Driver C-4735

  8. Install a NEW rear bearing on the pinion gear using Installer, Bearing C-3095-A and a press.

    1 – Press
    2 – Installer, Bearing C-3095-A
    3 – Rear Pinion Bearing
    4 – Pinion Gear

  9. Install a NEW collapsible spacer on the pinion shaft and apply Mopar® Thread Sealant to splines of the splines of the pinion shaft.

    1 – Collapsible Spacer
    2 – Mopar® Thread Sealant
  10. Align the marks on the pinion shaft and the companion flange and install using Installer, Flange C-3718 or Installer, Pinion Flange 2054200030 and Holder, Yoke 6719A .
  11. Install a NEW pinion nut.

    1 – Torque Wrench
    2 – Holder, Yoke
  12. Hold the companion flange using Holder, Yoke 6719A and tighten the pinion nut.
  13. Rotate the companion flange several times to seat the pinion bearings.

    1 – Inch Pound Torque Wrench
    2 – Companion Flange
  14. Measure Pinion Torque To Rotate (PTTR) using an inch pound torque wrench. Measure PTTR frequently to avoid over-crushing the collapsible spacer. Pinion Torque To Rotate is:

    • New Bearings: 1.9 - 2.5 N·m (17 - 22 in. lbs.)

      NOTE:

      If the PTTR is low, tighten the pinion nut in 6.8 N·m (5 ft. lbs.) increments until the PTTR is achieved.


      NOTE: Once proper PTTR is achieved, the pinion nut must be staked to the pinion to prevent pinion nut movement.
     

    CAUTION:

    Never loosen pinion nut to decrease pinion bearing rotating torque. If pinion torque to rotating is exceeded a new collapsible spacer must be installed. Failure to follow these instruction will damage the axle.


  15. Position the ring gear on the differential case and start two NEW ring gear bolts. This will provide case-to-ring gear bolt hole alignment.

    1 – Ring Gear Bolts
  16. Invert the differential case in the vise.
  17. Install NEW ring gear bolts and alternately tighten.

    CAUTION:

    Never reuse the ring gear bolts. Failure to follow these instruction will result in damage.

  18. Install the differential case in the housing (Refer to 03 - Differential and Driveline/ASSEMBLY, Differential/Removal and Installation) .
  19. Verify that gear mesh, backlash and contact patterns are within the proper specifications (Refer to 03 - Differential and Driveline/Adjustments) .
  20. Remove the support and lower the vehicle.
 

TORQUE SPECIFICATIONS - C235 DIFFERENTIAL


TORQUE SPECIFICATIONS - DRIVESHAFT