DRAIN PLUG, FILL PLUG AND VENT
|
CALLOUT
|
DESCRIPTION
|
SPECIFICATION
|
COMMENT
|
|
1
|
Differential Oil Drain Plug
|
35 N·m (26 Ft. Lbs.) |
–
|
|
2
|
Differential Oil Fill Plug
|
26 N·m (19 Ft. Lbs.) |
–
|
|
Not Shown
|
Axle Vent
|
27 N⋅m (20 Ft. Lbs.) |
–
|
DIFFERENTIAL COVER
|
CALLOUT
|
DESCRIPTION
|
SPECIFICATION
|
COMMENT
|
|
1
|
Differential Cover Bolts
|
44 N·m (32 Ft. Lbs.) |
–
|
E-LOCKER PASS THROUGH CONNETOR
|
CALLOUT
|
DESCRIPTION
|
SPECIFICATION
|
COMMENT
|
|
1
|
E-Locker Pass Through Connector Bolt
|
11 N·m (97 In. Lbs.) |
–
|
PINION FLANGE
 |
|
CALLOUT
|
DESCRIPTION
|
SPECIFICATION
|
COMMENT
|
|
1
|
Pinion Nut
|
- Hold the companion flange using Holder, Yoke 6719A and tighten the NEW pinion nut using a torque wrench to 272 N⋅m (201 Ft. Lbs.) .
- Rotate the pinion several times to ensure the pinion bearings are seated.
 |
|
| 1 – Inch Pound Torque Wrench |
| 2 – Companion Flange |
- Measure the PTTR with an inch pound torque wrench. PTTR should be equal to recorded reading plus an additional 0.56 N⋅m (5 In. Lbs.). If PTTR is low, tighten the pinion nut in 6.8 N⋅m (5 Ft. Lbs.) increments until the PTTR is achieved.
| CAUTION: |
Never loosen pinion nut to decrease pinion bearing rotating torque. If pinion torque to rotating is exceeded, a new collapsible spacer must be installed. Failure to follow these instructions will result in damage to the axle.
|
| NOTE: |
Once the proper PTTR is achieved, the pinion nut must be staked to the pinion to prevent pinion nut movement. |
|
Do not reuse this fastener. If removed, a NEW fastener must be installed and tightened to specifications.
|
DRAIN PLUG, FILL PLUG FRONT AXLE DISCONNECT, FRONT AXLE TUBE, FRONT AXLE MOUNTS
|
CALLOUT
|
DESCRIPTION
|
SPECIFICATION
|
COMMENT
|
|
1
|
Front Axle Disconnect(FAD) Actuator Bolts
|
28 N⋅m (21 Ft. Lbs.) |
–
|
|
2
|
Fill Plug
|
35 N⋅m (26 Ft. Lbs.) |
–
|
|
3
|
Drain Plug
|
35 N⋅m (26 Ft. Lbs.) |
–
|
DIFFERENTIAL MOUNT BRACKET AND PINION BRACKET
|
CALLOUT
|
DESCRIPTION
|
SPECIFICATION
|
COMMENT
|
|
1
|
Differential Mount Bracket to Engine Block
|
63 N·m (46 Ft. Lbs.) |
These bolts also go through the left engine mount bracket
|
|
2
|
Differential Mount Bracket to Engine
|
63 N·m (46 Ft. Lbs.) |
–
|
|
3
|
Differential Mount Bracket to Pinion Mount Bracket
|
80 N·m (59 Ft. Lbs.) |
–
|
|
4
|
Pinion Mount Bracket to Differential
|
110 N·m (81 Ft. Lbs.) |
–
|
|
CALLOUT
|
DESCRIPTION
|
SPECIFICATION
|
COMMENT
|
|
1
|
Engine Front Support to Axle RH
|
110 N⋅m (81 Ft. Lbs.) |
–
|
|
2
|
Engine Front Support to Axle LH
|
110 N⋅m (81 Ft. Lbs.) |
–
|