2023 Ram 1500

Removal and Installation

C235 – Thermal Rear Axle

▸Contents: 03 - Differential and Driveline

REMOVAL

  1. Disconnect and isolate the negative battery cable(s) (Refer to 08 - Electrical/Battery System/Standard Procedure) .
  2. Raise and support the vehicle (Refer to 04 - Vehicle Quick Reference/Hoisting - Standard Procedure) .
  3. Drain the cooling system (Refer to 09 - Engine/Cooling Systems/Engine Cooling/Standard Procedure) .
  4. Remove the coolant lines to differential cover nuts.

    1 - Coolant Lines to Differential Cover Nuts

  5. Remove the coolant lines from the mounting studs and DISCARD the seals.

    1 - Coolant Lines

  6. Remove the coolant line bracket to differential housing nuts on the differential and position the lines aside.

    1 - Coolant Line Bracket to Differential Housing Nuts
  7. Remove both rear wheels (Refer to 22 - Tires and Wheels/Removal and Installation) .
  8. Disconnect both rear wheel speed sensor wire harness connectors. (Air suspension shown, Coil suspension rear wheel speed sensor wire harness connector location and bracket location identical.)

    1 - Rear Brake Hose Routing Bracket Bolt
    2 - Rear Wheel Speed Sensor Wire Harness Connector
  9. Remove both rear caliper adapters (Refer to 05 - Brakes, Base/Hydraulic/Mechanical/ADAPTER, Disc Brake Caliper/Installation) .
  10. Loosen the clamp and disconnect the axle vent hose from the axle.

    1 - Vent Hose
  11. Remove the rear driveshaft (Refer to 03 - Differential and Driveline/SHAFTS, Axle/Drive/Half/Removal and Installation) .
  12. Remove the stabilizer bar bolts, the stabilizer bar brackets and position aside the sway bar.

    1 - Stabilizer Bar Bolts
    2 - Stabilizer Bar Brackets
  13. Position a lift under the axle and secure the axle to the lift.
  14. Remove and DISCARD the track bar axle bolt.

    1 - Track Bar Frame Bolt
    2 - Track Bar Axle Bolt

  15. Remove and DISCARD the upper control arm bracket bolts and nuts and position the upper control arms aside away from the axle.

    1 - Upper Control Arms
    2 - Upper Control Arm Bolts And Nuts At Axle

  16. Remove both lower shock absorber bolts and nuts and position the shock absorbers away from the axle.

    1 - Lower Shock Absorber Bolts And Nuts
    2 - Shock Absorber

  17. Remove and DISCARD the lower control arm bolts and nuts and position the control arm away from the rear axle.

    1 - Lower Control Arm Bolts And Nuts
    2 - Lower Control Arm

  18. Slightly lower the rear axle assembly and remove the rear coil springs.

    1 - Rear Axle Assembly
    2 - Coil Springs
  19. Remove the rear axle from the vehicle.
 

INSTALLATION



NOTE:

All suspension torques should be made with the full vehicle weight on the ground being supported by the tires.

  1. Position the coil springs in place on the rear axle and align into the spring upper pocket.
  2. Carefully raise the rear axle in place.

    1 - Rear Axle Assembly
    2 - Coil Springs

  3. Position both the lower control arms into the rear axle brackets and loosely install the NEW lower control arm bolts and nuts.

    1 - Lower Control Arm Bolts And Nuts
    2 - Lower Control Arm

  4. Position both the upper control arms in the rear axle brackets and loosely install the NEW upper control arm bolts and nuts.

    1 - Upper Control Arms
    2 - Upper Control Arm Bolts And Nuts At Axle

  5. Position both the rear shock absorbers in the axle brackets and loosely install the rear shock absorber bolts and nuts.

    1 - Lower Shock Absorber Bolts And Nuts
    2 - Shock Absorber

  6. Position the track bar on the axle and loosely install the NEW the track bar axle bolt.

    1 - Track Bar Frame Bolt
    2 - Track Bar Axle Bolt
  7. Remove the axle lift.

    NOTE:

    The stabilizer bar must be centered with equal spacing on both sides.


  8. Position the stabilizer bar in position and install the stabilizer brackets to the rear axle.

    1 - Stabilizer Bar Bolts
    2 - Stabilizer Bar Brackets

  9. Connect the axle vent hose to the axle and install the clamp.

    1 - Vent Hose
  10. Install the both rear caliper adapters (Refer to 05 - Brakes, Base/Hydraulic/Mechanical/ADAPTER, Disc Brake Caliper/Installation) .
  11. Connect the rear wheel speed sensor wire harness connectors.

    1 - Rear Brake Hose Routing Bracket Bolt
    2 - Rear Wheel Speed Sensor Wire Harness Connector

  12. Install the retaining nuts on the differential.

    1 - Coolant Line Bracket to Differential Housing Nuts

  13. Install the lines with NEW seals to the differential mounting studs.

    1 - Coolant Lines

  14. Install the coolant lines to differential cover nuts.

    1 - Coolant Lines to Differential Cover Nuts
  15. Fill the axle with the specified lubricant to the proper level (Refer to 04 - Vehicle Quick Reference/Capacities and Recommended Fluids/Specifications) .
  16. Install the rear driveshaft (Refer to 03 - Differential and Driveline/SHAFTS, Axle/Drive/Half/Removal and Installation) .
  17. Install the rear wheels (Refer to 22 - Tires and Wheels/Removal and Installation) .
  18. Remove the supports and lower the vehicle to properly load the suspension.
  19. Tighten the upper control arm bolts and nuts.

    1 - Upper Control Arms
    2 - Upper Control Arm Bolts And Nuts At Axle

  20. Tighten the lower control arm bolts and nuts.

    1 - Lower Control Arm Bolts And Nuts
    2 - Lower Control Arms

  21. Tighten the track bar axle bolt.

    1 - Track Bar Frame Bolt
    2 - Track Bar Axle Bolt

  22. Tighten the shock bolts and nuts.

    1 - Lower Shock Absorber Bolts And Nuts
    2 - Shock Absorber
  23. Fill the cooling system (Refer to 09 - Engine/Cooling Systems/Engine Cooling/Standard Procedure) .
  24. Connect the negative battery cable(s) (Refer to 08 - Electrical/Battery System/Standard Procedure) .
 

TORQUE SPECIFICATIONS - C235 DIFFERENTIAL


TORQUE SPECIFICATIONS - DRIVESHAFT


TORQUE SPECIFICATIONS - BRAKES BASE


TORQUE SPECIFICATIONS - WHEEL LUG NUT


TORQUE SPECIFICATIONS - REAR SUSPENSION