2023 Ram 1500

Removal and Installation

Rba260 – With Air Suspension

▸Contents: 03 - Differential and Driveline

REMOVAL

  1. Raise and support the vehicle (Refer to 04 - Vehicle Quick Reference/Hoisting - Standard Procedure) .
  2. With a scan tool, using the routines under the ASCM, perform the following:

    • Disable the air suspension system.
    • Run the Spring Deflate To Reservoir routine on the air suspension spring to be removed.
     
  3. Disconnect and isolate the negative battery cable(s) (Refer to 08 - Electrical/Battery System/Standard Procedure) .
  4. Remove both rear wheels (Refer to 22 - Tires and Wheels/Removal and Installation) .
  5. Disconnect both rear wheel speed sensor wire harness connectors.

    1 – Rear Brake Hose Routing Bracket Bolt
    2 – Rear Wheel Speed Sensor Wire Harness Connector
  6. Remove both rear caliper adapters (Refer to 05 - Brakes, Base/Hydraulic/Mechanical/ADAPTER, Disc Brake Caliper/Installation) .
  7. Loosen the clamp and disconnect the axle vent hose from the axle.

    1 – Vent Hose
  8. Remove the rear driveshaft (Refer to 03 - Differential and Driveline/SHAFTS, Axle/Drive/Half/Removal and Installation) .
  9. Remove the stabilizer bar bolts and position the stabilizer bar and stabilizer brackets aside or hang from wire off of the spare tire.

    1 – Stabilizer Bar Bolts
    2 – Stabilizer Bar Brackets
  10. Position a lift under the axle and secure the axle to the lift.
  11. Remove and DISCARD the track bar axle bolt.

    1 – Track Bar Frame Bolt
    2 – Track Bar Axle Bolt

  12. Carefully unsnap the lower end of the left and right height sensor level arms from the ball stud of the lower control arms with a small screwdriver.

    1 – Height Sensor Wire Harness Connector
    2 – Height Sensor Level Arm

  13. Remove both lower shock absorber bolts and nuts and position the shock absorbers away from the axle.

    1 – Lower Shock Absorber Bolts And Nuts
    2 – Shock Absorber

  14. Remove and DISCARD the lower control arm bolts and nuts and position the control arm away from the rear axle.

    1 – Lower Control Arm Bolts And Nuts
    2 – Lower Control Arm
  15. Remove the rear springs (Refer to 17 - Rear Suspension/SPRING(S) /Removal and Installation) .
  16. Remove the rear axle from the vehicle.
 

INSTALLATION



NOTE:

All suspension torques should be made with the full vehicle weight on the ground being supported by the tires.

  1. Install the rear springs (Refer to 17 - Rear Suspension/SPRING(S) /Removal and Installation) .
  2. Carefully raise the rear axle in place using a transmission jack or suitable lift.
  3. Position both the lower control arms into the rear axle brackets and loosely install the NEW lower control arm bolts and nuts.

    1 – Lower Control Arm Bolts And Nuts
    2 – Lower Control Arm

  4. Position both the upper control arms in the rear axle brackets and loosely install the NEW upper control arm bolts and nuts.

    1 – Upper Control Arms
    2 – Upper Control Arm Bolts And Nuts At Axle

  5. Position both the rear shock absorbers in the axle brackets and loosely install the rear shock absorber bolts and nuts.

    1 – Lower Shock Absorber Bolts And Nuts
    2 – Shock Absorber

  6. Position the track bar on the axle and loosely install the NEW the track bar axle bolt.

    1 – Track Bar Frame Bolt
    2 – Track Bar Axle Bolt
  7. Remove the axle lift.

    NOTE:

    The stabilizer bar must be centered with equal spacing on both sides.


  8. Position the stabilizer bar in position and install the stabilizer brackets to the rear axle.

    1 – Stabilizer Bar Bolts
    2 – Stabilizer Bar Brackets

  9. Connect the axle vent hose to the axle and install the clamp.

    1 – Vent Hose
  10. Install the both rear caliper adapters (Refer to 05 - Brakes, Base/Hydraulic/Mechanical/ADAPTER, Disc Brake Caliper/Installation) .
  11. Connect the rear wheel speed sensor wire harness connectors.

    1 – Rear Brake Hose Routing Bracket Bolt
    2 – Rear Wheel Speed Sensor Wire Harness Connector

  12. Carefully snap the lower end of the left and right height sensor level arms to the ball stud of the lower control arms.

    1 – Height Sensor Wire Harness Connector
    2 – Height Sensor Level Arm
  13. Install the rear driveshaft (Refer to 03 - Differential and Driveline/SHAFTS, Axle/Drive/Half/Removal and Installation) .
  14. Install the rear wheels (Refer to 22 - Tires and Wheels/Removal and Installation) .
  15. Fill the rear differential using the specified fluid to the proper level (Refer to 04 - Vehicle Quick Reference/Capacities and Recommended Fluids/Specifications) .
  16. Remove the supports and lower the vehicle.
  17. Connect the negative battery cable(s) (Refer to 08 - Electrical/Battery System/Standard Procedure) .
  18. Using a scan tool, under the Air Suspension Control Module (ASCM), perform the following:

    • Command the vehicle to Normal Ride Height.
    • Run the Air Mass Calculation routine on the air suspension system.
    • If necessary, add to the system or deflate to atmosphere using the ASCM routines, then repeat the Air Mass Calculation routine again until system responds with Air Mass OK (188 - 216 bar-liters).
    • Enable the air suspension system.
     
  19. Tighten the upper control arm bolts and nuts.

    1 – Upper Control Arms
    2 – Upper Control Arm Bolts And Nuts At Axle

  20. Tighten the lower control arm bolts and nuts. Position both the rear shock absorbers in the axle brackets and loosely install the rear shock absorber bolts and nuts.

    1 – Lower Control Arm Bolts And Nuts
    2 – Lower Control Arm

  21. Tighten the track bar axle bolt.

    1 – Track Bar Frame Bolt
    2 – Track Bar Axle Bolt

  22. Tighten the shock bolts and nuts.

    1 – Lower Shock Absorber Bolts And Nuts
    2 – Shock Absorber
  23. Perform the ASCM Verification Test (Refer to 28 - DTC-Based Diagnostics/MODULE, Air Suspension Control (ASCM) /Standard Procedure) .
 

TORQUE SPECIFICATIONS - RBA260 INTERNAL


TORQUE SPECIFICATIONS - DRIVESHAFT


TORQUE SPECIFICATIONS - BRAKES BASE


TORQUE SPECIFICATIONS - WHEEL LUG NUT


TORQUE SPECIFICATIONS - REAR SUSPENSION