2023 Ram 1500

Removal and Installation

Differential Assembly - Rba260 - Electric Locking

▸Contents: 03 - Differential and Driveline

REMOVAL

  1. Raise and support the vehicle (Refer to 04 - Vehicle Quick Reference/Hoisting/Standard Procedure) .
  2. Remove the differential cover (Refer to 03 - Differential and Driveline/COVER/Removal and Installation) .
  3. Remove the axle shafts (Refer to 03 - Differential and Driveline/SHAFTS, Axle/Drive/Half/Removal and Installation) .
  4. Disconnect the electric locker wire harness connector from the pass through connector.

    1 – Electric Locker Wire Harness Pass Through Connector Bolt
    2 – Electric Locker Wire Harness Pass Through Connector
  5. Remove the electric locker wire harness pass through connector bolt.
  6. Disconnect the internal electric locker harness connector from the pass through connector and remove the pass through connector.

    1 – Internal Electric Locker Harness Connector
    2 – Electric Locker Actuator Anti Rotation Tabs
  7. Mark the differential housing and bearing caps for installation reference.
  8. Remove both adjuster lock bolts and remove the adjuster lock tabs.

    1 – Adjuster Lock Bolt
    2 – Adjuster Lock Tab

  9. Loosen the differential bearing cap bolts.

    1 – Differential Bearing Cap Bolts
    2 – Differential Bearing Cap

  10. Loosen the differential bearing adjusters through the axle tubes using Wrench, Differential Preload C-4164 .

    1 – Wrench, Differential Preload C-4164
    2 – Axle Tube
  11. Hold the differential case while removing the bearing caps.

    NOTE:

    Tag the differential bearing cups and the threaded adjusters after removal to indicate their location.

  12. Remove the differential case.

    NOTE:

    Side play resulting from bearing races being loose on case hubs requires replacement of the differential case.

  13. Clean the housing cavity with brake cleaner and a lint free cloth.

    NOTE:

    Do not use steam, kerosene or gasoline to clean the housing.


 

INSTALLATION

  1. Apply a coating of hypoid gear lubricant to the differential bearings and bearing cups.
  2. Install the differential assembly into the housing making sure the electric locker actuator anti rotation tabs are located against the left side of the housing.

    1 – Internal Electric Locker Harness Connector
    2 – Electric Locker Actuator Anti Rotation Tabs

  3. Install the differential bearing caps in their original locations.

    1 – Differential Bearing Cap Bolts
    2 – Differential Bearing Cap
  4. Install bearing cap bolts and tighten the upper bolts to 14 N⋅m (10 ft. lbs.). Tighten the lower bolts finger-tight until the bolt head is seated.
  5. Position the pass through connector and connect the internal electric locker harness connector to the and the pass through connector.

    1 – Internal Electric Locker Harness Connector
    2 – Electric Locker Actuator Anti Rotation Tabs

  6. Install the pass through connector bolt.

    1 – Electric Locker Wire Harness Pass Through Connector Bolt
    2 – Electric Locker Wire Harness Pass Through Connector
  7. Perform the differential bearing preload and adjustment procedure (Refer to 03 - Differential and Driveline/Adjustments) .

    NOTE:

    Verify that all of the bearing cap bolts are tightened to the proper (Refer to 03 - Differential and Driveline/Technical Specifications) before proceeding.

  8. Install the axle shafts (Refer to 03 - Differential and Driveline/SHAFTS, Axle/Drive/Half/Removal and Installation) .
  9. Install the differential cover (Refer to 03 - Differential and Driveline/COVER/Removal and Installation) .
  10. Fill the differential with lubricant to the proper specification (Refer to 04 - Vehicle Quick Reference/Capacities and Recommended Fluids - Specifications) .
  11. Remove the support and lower the vehicle.
 

TORQUE SPECIFICATIONS - RBA260 INTERNAL